MITSUBISHI ELECTRIC FR-S520E - Manual (Page 7)

II
1.5.3 Current input selection "AU signal": Pr. 60 to Pr. 63 setting "4".................. 37
1.5.4 Start self-holding selection (STOP signal): Pr. 60 to Pr. 63 setting "5" ....... 38
1.5.5 Output shut-off (MRS signal): Pr. 60 to Pr. 63 setting "6" ........................... 38
1.5.6 External thermal relay input: Pr. 60 to Pr. 63 setting "7" ............................. 39
1.5.7 Jog operation (JOG signal): Pr. 60 to Pr. 63 setting "9".............................. 39
1.5.8 Reset signal: Pr. 60 to Pr. 63 setting "10" ................................................... 40
1.5.9 PID control valid terminal: Pr. 60 to Pr. 63 setting "14"............................... 41
1.5.10 PU operation/external operation switchover: Pr. 60 to Pr. 63 setting "16" .. 41
1.6 Connection to the Stand-Alone Option................................. 42
1.6.1 Connection of the dedicated external brake resistor (option) (FR-S520E-0.4K
to 3.7K only) ................................................................................................ 42
1.6.2 Connection of the brake unit (BU type) ....................................................... 43
1.6.3 Connection of the high power factor converter (FR-HC)............................. 44
1.6.4 Connection of the power regeneration common converter (FR-CV)........... 45
1.7 Handling of the RS-485 connector ........................................ 46
1.7.1 Connection of the parameter unit (FR-PU04) ............................................. 46
1.7.2 Wiring of RS-485 communication ............................................................... 47
1.8 Design information ................................................................. 50
2. FUNCTIONS 51
2.1 Function (Parameter) list........................................................ 52
2.2 List of parameters classified by purpose of use.................. 65
2.3 Explanation of functions (parameters) ................................. 67
2.3.1 Torque boost (Pr. 0 , Pr. 46 ) ...................................................................... 67
2.3.2 Maximum and minimum frequency (Pr. 1 , Pr. 2 ) ...................................... 68
2.3.3 Base frequency, base frequency voltage (Pr.3 , Pr.19 , Pr.47 ).................. 69
2.3.4 Multi-speed operation (Pr. 4, Pr. 5, Pr. 6, Pr. 24 to Pr. 27, Pr. 80 to Pr. 87)70
2.3.5 Acceleration/deceleration time (Pr. 7 , Pr. 8 , Pr. 20 , Pr. 44 , Pr. 45 ) ....... 71
2.3.6 Selection and protection of a motor (Pr. 9 , Pr. 71 , H7 ) ............................ 73
2.3.7 DC injection brake (Pr. 10 , Pr. 11 , Pr. 12 ) ............................................... 75
2.3.8 Starting frequency (Pr. 13 ) ......................................................................... 76
2.3.9 Load pattern selection (Pr. 14 )................................................................... 77
2.3.10 Jog operation (Pr.15 , Pr.16 )...................................................................... 78
2.3.11 RUN key rotation direction selection (Pr.17 ) .............................................. 78
2.3.12 Stall prevention function and current limit function (Pr. 21 ) ....................... 79
2.3.13 Stall prevention (Pr. 22 , Pr. 23 , Pr. 28 ) .................................................... 81
2.3.14 Acceleration/deceleration pattern (Pr. 29 ) ................................................. 83