Gasboy 1000 Series Technical Reference Manual - Manual (Page 52)

GASBOY Series 1000
2-34 03/07/03
If you want to have the supervisor enter CARD NUMBER, ID FIELD 1, and ID
FIELD 2, encode the following in those fields:
ÂÂB–ÂUaUVAI–ÂÂB–Â97T@–ÂBEAH@!–ÂBEAH@"–ÂÂB–ÂA`R–ÂRTQ@–ÂRTQ@–Â9DA9GÂ
ÂÂU–ÂÂÂE@–ÂÂU–ÂPQ–ÂAIR–ÂXAD–ÂÂU–Â@7VA–ÂHEI–Â7WVD–Â@ECEVÂ
–ÂÂ````––Â7777–ÂÂAAAA–ÂÂ7777––ÂaaII–ÂÂÂ`–ÂÂÂ`–ÂÂÂ`ÂÂÂ
If you want to have the supervisor enter only ID FIELD 1, encode the card as
follows:
ÂÂB–ÂUaUVAI–ÂÂB–Â97T@–ÂBEAH@!–ÂBEAH@"–ÂÂB–ÂA`R–ÂRTQ@–ÂRTQ@–Â9DA9GÂ
ÂÂU–ÂÂE@–ÂÂU–ÂPQ–ÂAIR–ÂXAD–ÂÂU–Â@7VA–ÂHEI–Â7WVD–Â@ECEVÂ
–ÂÂ````––Â````–ÂÂ7777–ÂÂ````––ÂaaII–ÂÂÂ`–ÂÂÂ`–ÂÂÂ`ÂÂÂ
CFN Network For Commercial Fueling Networks, the supervisor can enter data in one to three
of these fields: CARD, ACCOUNT and VEHICLE.
A supervisor card is encoded with special characters (A or E) that designate
which fields (Card Number, Account, or Vehicle) should be entered manually.
The fields to be manually entered must be filled with either all As or all Es. When
the Supervisor card is used to enter data into the CARD field, the last digit on the
card must be encoded and it must match either the A or the E used in the card
field. For example, assume that your CFN network system has the following card
layout:
ÂB–ÂUaU–ÂB–ÂÂ97T@–Â799V–ÂXAD–ÂB–ÂA`R–ÂRTQ@–ÂRTQ@–ÂRTE–9DA9G–Â97T@Â
ÂU–ÂE@–ÂU–ÂÂÂƖ––ÂU–Â@7VA–ÂHEI–Â7WVD–ÂHXH–@ECEV–ÂIU@ÂÂ
–Â````––Â``````–Â`````````–Â````––ÂaaII–ÂÂÂ`–ÂÂ``–ÂÂ`–ÂÂ`–ÂÂ`Â
X = digit (0-9), FS = field separator
If you want to have the supervisor enter Card Number, Account, and Vehicle,
encode the following in those fields:
ÂB–ÂUaU–ÂB–ÂÂ97T@–Â799V–ÂXAD–ÂB–ÂA`R–ÂRTQ@–ÂRTQ@–ÂRTE–9DA9G–Â97T@Â
ÂU–ÂE@–ÂU–ÂÂÂƖ––ÂU–Â@7VA–ÂHEI–Â7WVD–ÂHXH–@ECEV–ÂIU@Â
–Â````––Â777777–ÂAAAAAAAAA–Â7777––ÂaaII–ÂÂÂ`–ÂÂ``–ÂÂ`–ÂÂ`–ÂÂ7Â
Optical Card
Systems
Any card with a card number in the range 9930-9979 is treated as a supervisor
card. When a supervisor card is used, ID FIELD 1 and ID FIELD 2 may be
entered through the keypad. The data entered at the keypad replaces any data
that may have been on the card in those fields. If you do not enter any data and
just press ENTER, the system uses the data from the card.