Gasboy Atlas Technician Programming Quick Ref - Manual

Command Code 7:
Program Totals Input
Press Enter after making selections.
• Enter 7
• Select Side
1 : Side A
2 : Side B
• Select Grade
• Press $ Total
• Enter Money Total
(Repeat for other Side and Grade)
• Press Volume Total
(Repeat above procedure for Volume
Totals)
Command Code 8:
Display Version Number
Press Enter after making selections.
• Enter 8
• Select Software Option
1 : Pump Controller
* Default to system software, if
pump/dispenser is not a Blender.
**1 : Side A
2 : Side B
3 : Both Sides
From Level 2
Command Code 10:
System Configuration
Press Enter after making selections.
• Enter 10.
• Enter Function #.
• Enter Configuration #.
Function Code 2:
Money Decimal Point
1 = xxxxx
2 = xxxx.x
3 = xxx.xx***
4 = xxx.xxx
Function Code 3:
Calculation PPU Decimal Point
(Required in U.S. per Weights and
Measures)
1 = xxxx
2 = xxx.x
3 = xx.xx
4 = x.xxx***
Function Code 4:
Displayed PPU Decimal Point
Self configures default value.
1 = xxxx
2 = xxx.x
3 = xx.xx
4 = x.xxx
Function Code 5:
STP Prestart
0 = Off***
1 = On
Function Code 6:
Beeper Option
0 = Off
1 = On***
Function Code 8:
Two-Wire Display Blank Option
0 = Off***
1 = On
Function Code 9:
5 or 6-digit Cash Display
0 = 5-Digit Money***
1 = 6-Digit Money
Function Code 10:
Decimal/Comma Mode
0 = Comma Off***
1 = Comma On
Function Code 11:
Preselect Time-Out
0 = None
1 = 5 seconds
2 = 15 seconds***
3 = 30 seconds
4 = 45 seconds
5 = 60 seconds
6 = 75 seconds
7 = 90 seconds
8 = 120 seconds
Function Code 14:
G6 Push to Start
0 = Off***
1 = On
Function Code 15:
Zero PPU Pricing Option Enable
0 = Disabled***
1 = Enabled
Function Code 16:
Beeper Time-out
0 = Off***
1 = 5 seconds
2 = 15 seconds
3 = 30 seconds
4 = 45 seconds
5 = 60 seconds
6 = 75 seconds
7 = 90 seconds
8 = 120 seconds
9 = 240 seconds
Function Code 17:
Push to Stop Control
0 = Stop controls one side***
1 = Stop controls two sides
Function Code 18:
Zero Previous Transaction After
Pump Handle Operation
0 = Zero after lamp test***
1 = Zero before lamp test†
Function Code 20:
Programmable Pump Preset Value
0 = Value x 1 (enter fractions)
1 = Value x 10 (enter whole units)
MDE-4404A
Atlas ™ Technician Programming
Quick Reference Card
July 2010
From Level 1
Command Code 1:
Program PPU
Press Enter after making selections.
• Enter 1
• Select Side**
• Select Grade
• Select Price Level
• Enter new PPU
(Repeat for other Side, Grade, and
Price Level)
Command Code 2:
Program Two-Wire/Standalone
Press Enter after making selections.
• Enter 2
• Select Configuration
0 : Standalone
1 : Two-Wire*
2 : Pulse Output
Command Code 3:
Program Allocation
Press Enter after making selections.
• Enter 3
• Select Side**
• Select Hose/Grade
• Enter Allocation amount
(000.0 default)
(Repeat for other Side, Hose, and
Grade)
Command Code 4:
Program Manual Blank Display
Cash/Volume Preset Select
Press Enter after making selections.
• Enter 4
Select Function Code 1
Function Code 1:
Manual Blank Displays
0 : Display OFF
1 : Display ON*
Command Code 5:
Test/Program
Customer Programmable Preset
Press Enter after making selections.
• Enter 5
• Select Configuration
0 : STOP Test/Program
1 : START Test/Program
(After the test is complete, refer to the
programming steps in MDE-2531
Pump/Dispenser Service Manual.)
Command Code 6:
Memory Clear for Error Code 31
or 35
Press Enter after making selections.
• Enter 6
• Select 1
Software Versions
For details on software versions, refer to MDE-4331 Atlas ™ Fuel Systems
Installation Manual, MDE-4334 Atlas Startup and Service Manual, and MDE-4363
Atlas Fuel Systems Owner’s Manual.
Power-up and Command Code 8 display the current software version.
Display Pump Totals
• Press Enter after making selections.
• Press $ Total
• Select Grade
• Press Volume Total
• Select Grade
• Press Enter to view Side 2 totals
• Press Clear to exit
PIN Code Entry
Level 1 - Press F1, type 4-digit ID (default 2222), and press Enter.
Level 2 - From Level 1, type any Level 2 Command Code (10-12), type 4-digit ID
(default 1503), and press Enter.
Level 3 - From Level 2, type any Level 3 Command Code (13-17), type 4-digit ID
(default 1309), and press Enter.
Press F1 to exit any command code.
Press F2 to return to normal operation