7 sensor device commands, Table 7-7, Supported sensor device commands – Artesyn CPCI-6200 Installation and Use (May 2015) User Manual
Page 158: Control via ipmi
Control via IPMI
CPCI-6200 Installation and Use (6806800J66E)
158
7.1.7
Sensor Device Commands
The IPMC supports the following sensor device commands.
Table 7-7 Supported Sensor Device Commands
Command
NetFn
(Request/Response) CMD
Comments
Get Device SDR Info
0x04/0x05
0x20
-
Get Device SDR
0x04/0x05
0x21
-
Reserve Device SDR Repository
0x04/0x05
0x22
-
Get Sensor Reading Factors
0x04/0x05
0x23
-
Set Sensor Hysteresis
0x04/0x05
0x24
-
Get Sensor Hysteresis
0x04/0x05
0x25
-
Set Sensor Threshold
0x04/0x05
0x26
Most of the threshold-based
sensors have fixed thresholds.
Before using this command,
check whether threshold setting
is supported by using the Get
Device SDR command.
Get Sensor Threshold
0x04/0x05
0x27
-
Set Sensor Event Enable
0x04/0x05
0x28
-
Get Sensor Event Enable
0x04/0x05
0x29
-
Rearm Sensor Events
0x04/0x05
0x2A
-
Get Sensor Reading
0x04/0x05
0x2D
-
Set Sensor Type
0x2E
Get Sensor Type
0x04/0x05
0x2F
-
Set Event Receiver
0x04/0x05
0x00
-
Get Event receiver
0x04/0x05
0x01
-
Platform Event
0x04/0x05
0x02
-
- ARTM-9405 16x10GbE Installation and Use Guide (May 2014) (64 pages)
- ATCA 7370 / ATCA 7370-S Installation and Use (January 2015) (256 pages)
- ATCA 7370 / ATCA 7370-S Installation and Use (September 2014) (254 pages)
- ARTM-831X Installation and Use (June 2014) (346 pages)
- ATCA-7350 - Integrating with Workbench User Guide (September 2014) (34 pages)
- ATCA-7350 Installation and Use (September 2014) (208 pages)
- ATCA-7365-CE Installation and Use (May 2014) (306 pages)
- ATCA-7365-CE Installation and Use (Jan 2015) (300 pages)
- ATCA-7365-CE Installation and Use (May 2014) (294 pages)
- ATCA-7368 Installation and Use (June 2014) (222 pages)
- ATCA-7475 Installation and Use (October 2014) (284 pages)
- ATCA-7480 Installation and Use (April 2015) (330 pages)
- ATCA-8330 Installation and Use (April 2015) (236 pages)
- ATCA-8320 Installation and Use (May 2014) (456 pages)
- ATCA-9305 User's Manual (May 2014) (270 pages)
- ATCA-9405 Installation and Use (October 2014) (168 pages)
- ATCA-F120 Installation and Use (August 2014) (122 pages)
- ATCA-F140 Installation and Use (September 2014) (138 pages)
- ATCA-MF106 Installation and Use (September 2014) (86 pages)
- Centellis-4440/AXP1440 Installation and Use (September 2014) (208 pages)
- Centellis 4410 (AXP-1410) Installation and Use (July 2014) (202 pages)
- Centellis 2100 Release 3.0 Installation and Use (March 2015) (176 pages)
- Centellis 2100 Release 3.0 Installation and Use (March 2015) (192 pages)
- Centellis 2000 User Card-10GE Installation and Use (May 2014) (54 pages)
- Centellis 2000 User Card-10GE with Telco Alarm Installation and Use (May 2014) (60 pages)
- COMX-CAR-210 Installation and Use (August 2014) (76 pages)
- COMX-P1022 Installation and Use (July 2014) (84 pages)
- COMX-P2020 Installation and Use (February 2015) (100 pages)
- COMX-CORE Series Installation and Use (August 2014) (128 pages)
- COMX-P2020 Installation and Use (July 2014) (100 pages)
- COMX-P4080-2G-ENP2 Installation and Use (August 2014) (70 pages)
- COMX-P4080 Installation and Use (August 2014) (126 pages)
- COMX-P40x0 ENP2 Installation and Use (August 2014) (130 pages)
- COMX-P40x0 ENP2 Installation and Use (January 2015) (140 pages)
- iVPX7225 RTM Installation and Use (April 2015) (56 pages)
- MITX-430/MITX-440-DVI-2E Installation and Use (August 2014) (118 pages)
- SCP-MITX-CORE-820-SM Installation and Use (August 2014) (132 pages)
- iVPX7225 Installation and Use (April 2015) (168 pages)
- MVME2502 Installation and Use (August 2014) (150 pages)
- MVME2502 Installation and Use (December 2014) (166 pages)
- MVME2500 VxWorks 6.8 AMP User Guide (August 2014) (40 pages)
- MVME2500 VxWorks 6.8 User Guide (April 2014) (44 pages)
- MVME3100 Single Board Computer Installation and Use (June 2014) (156 pages)
- MVME4100 Single Board Computer Installation and Use (June 2014) (136 pages)