Tips ( t2 ), Page 7 - 28 tank sentinel, Installation guide – Franklin Fueling Systems Tank Sentinel (TS-1001, 2001, 504, 508 & 750) Installation User Manual
Page 71
7
Page
7 - 28
TANK SENTINEL
®
INSTALLATION GUIDE
Some AC input modules are dual-purpose and can be used as DC input
modules. These dual-purpose modules are marked with an asterisk
*
in TABLE
7-5.
•
Match I/O module to the power source Voltage Type (AC or DC)
•
Match I/O module to the Power Source voltage level (never exceed 250 volts)
•
Match I/O output modules to the current draw of the load (never exceed 1 amp
maximum – no matter what is printed on I/O module)
Figure 7-13c.
TS-IEM Internal Expansion Module – Component Location
Tips
(
T2
)
TS-IEM PC BOARD: SHOWN WITH 4 INPUT,
AND 4 OUTPUT MODULES
TS-IEM PC BOARD
J 1
I N / O U T 6
M T
I N / O U T 8
I N / O U T 7
1 7 0 - 1 0 5 8
AC
AC
AC
+
DC-
+
DC-
R L 6
+
DC-
R L 7
R L 8
I N / O U T 1
I N / O U T 3
I N / O U T 4
I N / O U T 5
I N / O U T 2
M T
AC
+
DC-
AC
AC
AC
AC
R L 2
R L 5
+D
C
-
+
DC-
+
DC-
+
DC-
R L 4
R L 3
J 2
R L 1
F4
A
+
DC-
+
DC-
+
DC-
I N / O U T 6
AC
AC
M T
M T
I N / O U T 8
I N / O U T 7
AC
1 7 0 - 1 0 5 8
J 1
R L 6
F4
A
x
W
S
F U S E
2 5 0 V
R L 8
F U S E
F4
A
x
W
S
R L 7
2 5 0 V
F4
A
x
W
S
2 5 0 V
F U S E
2 5 0 V
+
DC-
+D
C
-
+
DC-
+
DC-
+
DC-
AC
I N / O U T 1
I N / O U T 5
I N / O U T 4
I N / O U T 3
I N / O U T 2
AC
AC
AC
AC
M T
M T
R L 2
R L 3
R L 4
R L 5
F U S E
x
W
S
J 2
R L 1
INPUT _ _ _V_ _
OUTPUT _ _ _V_ _ _A
OUTPUT MODULE:
HAS FUSE AND 4 PINS
MATCH MODULE VOLTAGE LEVEL
TYPE(AC or DC) AND CURRENT
TO POWER SOURCE.
# 4-40 HOLD-DOWN SCREW (TYPICAL)
RED L.E.D. - ON WHEN MODULE
TURNS ON / VOLTAGE IS APPLIED.
INPUT MODULE: HAS 5 PINS
MATCH MODULE INPUT VOLTAGE
WITH POWER SOURCE VOLTAGE.
RED L.E.D. -- ON WHEN MODULE
TURNS ON.
WARNING VOLTAGE MAY BE PRESENT
AT THE INTERFACE TERMINALS
EVEN WHEN THE L.E.D. IS OFF.
WARNING: DO NOT INSTALL OR
REMOVE MODULES, FUSES, OR
WIRING WITH POWER APPLIED !
TURN THE TS-2001 POWER OFF.
LOCATE, DISCONNECT, AND
CHECK ALL EXTERNAL POWER
SOURCES FOR ABSENCE OF
VOLTAGE BEFORE WORKING ON
THESE CIRCUITS.
M T
2 5 0 V
F U S E
W
M T
F4
A
x
S
F U S E
2 5 0 V
F
4
A
W
x
S
FUSE REPLACEMENT
INSTALL ONLY
CORRECT RATING
REPLACEMENT
FUSES
F U S E
2 5 0 V
W
x
F4
A
S
Two different manufacturers of I/
0 modules are possible
(replacement fuses may be
different)