Figure 7-10. ts-lld tank gauge interface wiring, Page 7 - 22 tank sentinel, Installation guide – Franklin Fueling Systems Tank Sentinel (TS-1001, 2001, 504, 508 & 750) Installation User Manual
Page 65: Ts-lldi ( line leak detector interface ), Cu #2 cu #1 last cu #n cu #3
7
Page
7 - 22
TANK SENTINEL
®
INSTALLATION GUIDE
PO
W
E
R
IN
P
U
T
S
I N 2
G N D
L1
d d
G N D
I N 1
F 1 4
B 1
+
+
J 1 4
TB2-3 DSY1
P O W E R
O N
S W 1
O F F
TS
-
L
LD
S . R T N
D S Y
4 8 5 B
4 8 5 A
J 1 3
W A R N I N G: AVOID ELECTRICAL SHOCK HAZARDS.
EXTERNAL POWER SOUCES MAY BE PRESENT -
LOCATE AND DISCONNECT ALL EXTERNAL POWER
SOURCES BEFORE WIRING OR SERVICING
THESE CIRCUITS.
TS-LLDI ( Line Leak Detector Interface )
485B
COMM LINE
DSY
CONTROL UNIT I.D. LINE
S. RTN
RS-485 COMMUNICATIONS
SIGNAL RETURN
TANK / LINE #1
TS-LLD CU #1:
TS-1001 CONSOLE
TS-LLD INTERFACE
TERMINALS AT J13:
t
485A
COMM LINE
TANK / LINE #3
TS-LLD CU #3:
TANK / LINE #2
TS-LLD CU #2:
LAST TANK / LINE #N
TS-LLD CU #N:
TB2-4 DSY2
TB2-3 DSY1
TB2-2 485B
TB2-1 485A
t
TB1-SIG RTN
TB2-3 DSY1
TB1-SIG RTN
TB1-SIG RTN
TB2-4 DSY2
TB2-4 DSY2
TB2-2 485B
TB2-2 485B
TB2-1 485A
TB2-1 485A
t
TB2-3 DSY1
TB1-SIG RTN
TB2-4 DSY2
JUMPER
NEEDED
AT LAST
UNIT
ONLY
t
TB2-2 485B
TB2-1 485A
CU #2
CU #1
last CU #N
CU #3
4 P-IN
SIG RTN
TB1
UP
1 485A
2 485B
3 DSY1
4 DSY2
5 ALARM
F1
TB2
GND
RE
L
A
Y
O
U
T
P
U
T
S
N O 2
TS-LLD Control Unit (CU) box
Enlarged View
TS-LLD Control Unit (CU)
Interface Terminals:
F 1 6
F 1 7
F 1 5
SAF
E
T
Y
GN
D
J 1 6
J 1 5
C 2
N C 2
N O 1
C 1
N C 1
J 1 7
GN
D
L2
NOTE --- DO NOT
RUN COMMUNICATIONS
CABLE WITH LINE
VOLTAGE WIRES.
4 P-IN
COMMUNICATIONS CABLE: (4) 22 - 28 AWG (0.6 - 0.5 mm)
SIG RTN
THIS SHIELD MUST BE
IN PLACE BEFORE THE
COVER IS RE-INSTALLED.
GREEN CONNECTOR (J1)
TB1
3 P-OUT
2 NEU
1 110V
1 485A
2 485B
3 DSY1
4 DSY2
5 ALARM
F1
TB2
TS
-
LLD
4 8 5 B
TB1-SIG RTN
TS-LLD CU cover (back view)
TB2-2 (485B)
TB2-3 (DSY 1)
S . R T N
D S Y
TB2-1 (485A)
Enlarged View of
Terminal Strip # J13
4 8 5 A
NOTE:
1)
CAUTION BEFORE attempting this
installation: Read and reference the TS-LLD Manual
about Safety, and CU Installation (and wiring steps).
2)
WARNING
Avoid electrical shock hazards —
Turn off and disconnect all power to the pumps and
dispensers before wiring at the TS-LLD Control Units.
3)
Eight TS-LLD Control Units can be interfaced to
the TS-2001 console, and Four can be interfaced to the
TS-1001 console
Figure 7-10.
TS-LLD Tank Gauge Interface Wiring