Franklin Fueling Systems Tank Sentinel (TS-1001, 2001, 504, 508 & 750) Installation - Manual (Page 59)

7 Page 7 - 16 TANK SENTINEL ® INSTALLATION GUIDE
Figure 7-8c. TS-SEM BriteBox ® — Connection & Sensor Wiring Details
BRITEBUS (RIBBON CABLE) - TYPICAL
CONNECTION DIAGRAM
J2
BRITEBOX
# 2
J1 J2 J1
BRITEBOX
# 1
J11
OR
J2
BRITEBUS CABLE
RED STRIPE DOWN
(TYPICAL - BOTH ENDS)
J11
CONSOLE
MAIN PCBd
BRITEBUS RIBBON CABLE
DETAIL (RIGHT SIDE LOOPED)
TWO GREEN GROUND WIRES, THROUGH 1/2" (12.7 mm) CONDUIT TO ELECTRICAL PANEL:
EARTH GROUND (NEUTRAL BUSS BAR).
* (POWER) - TO RED COLORED SENSOR WIRES ONLY
(NO CONNECTION IS REQUIRED FOR 2 CONDUCTOR SENSOR CABLES)
* (GROUND) - TO BLACK COLORED SENSOR WIRES ONLY
* (INPUT) - TO WHITE COLORED SENSOR WIRES ONLY
3/4" CONDUIT
FOR
4 SENSORS
HAZARDOUS LOCATION (CLASS I, DIV 1, GROUP D -
NON-HAZARDOUS LOCATION
SEN
SO
R
3/
7
PWR (RED)
IN (WHT)
GND (BLK)
GND (BLK)
SEN
SO
R
4/
8
Enlarged View
Typical for: J5 & J3
IN (WHT)
PWR (RED)
IN (WHT)
GND (BLK)
IN (WHT)
GND (BLK)
PWR (RED)
PWR (RED)
SEN
SO
R
1/
5
SEN
SO
R
2/
6
INTRINSICALLY
SAFE WIRING
ONLY)
3/4" CONDUIT
FOR
4 SENSORS
SE NS OR 4
SE NS OR 5
GN D (BL K)
IN (W HT )
PW R (RED )
PW R (RED )
IN (W HT )
GN D (BL K)
PW R (RED )
IN (W HT )
GN D (BL K)
GN D (BL K)
IN (W HT )
SE NSOR 1
SE NS OR 3
SEN
SOR 2
EA RTH
GN D
EA RTH
GN D
SE NSOR 8 GN D (B LK )
PW R (RE D)
IN (W H T)
SEN
SOR 7
SE NS OR 6
GN D (B LK )
IN (W H T)
GN D (B LK )
IN (W H T)
PW R (RE D)
PW R (RE D)
GN D (B LK )
IN (W H T)
PW R (RED )
J2
D1
J4 J5 J3
PW R (RE D)
F1
J1
EARTH GND EARTH GND
J4
Enlarged
TS-SEM BriteBox #1
(OPTIONAL:
Sensor Expansion Module)
NOTE:
1) SEE N.E.C. / C.E.C. FOR INTRINSICALLY SAFE WIRING.
2) TYPICAL LEAK DETECTION SENSOR WIRING CONNECTIONS
ARE SHOWN.
3) SEE SENSOR INSTALLATION INSTRUCTION MANUAL(S)
FOR ADDITIONAL DETAILS.
4) * = MAX. CABLE LENGTH BETWEEN THE TS-SEM AND
ANY LEAK DETECTION SENSOR MUST NOT EXCEED 1500 FEET.
5) EACH GND TERMINAL MUST BE CONNECTED TO A
SUITABLE SYSTEM EARTH GROUND. DC RESISTANCE BETWEEN
GND TERMINALS AND EARTH GROUND MUST BE LESS THAN 1 OHM.
6) REMOVE THE JUMPER LINK BEFORE WIRING A SENSOR.
ONLY UNUSED SENSOR CHANNELS MUST HAVE THE
JUMPER WIRE INSTALLED BETWEEN THE IN & GND
TERMINALS.
J 8
U4
7
J 9
J 1 1
RIBBON CABLE
(INSTALLED WITH
RED STRIPE
DOWN -
TYPICAL
BOTH ENDS)
J 7
U 3 6
D 1 2 T X D
S 1
D 1 3
D 1 4
R X D
D T R
D 1 5
D C D
J 5
U 3 5
J 1 0
J 4
J 3
J 6
J 3 2
U 4 5
T P 3
J 1 2
M A I N
S Y S T E M
P C B d
1 7 0 - 1 0 5 4
D 2
U 1 0 TS-2001/N-N U10
VER No. DATE
J 2 2
J 2
J 1
T P 2
T P 1
J 3 3