Kontron AT8902 Full Size CLI User Manual
Kontron Hardware
Table of contents
Document Outline
- Revision History
- Imprint
- Disclaimer
- About This Book
- Why the Document was Created
- How to Use This Document
- Proprietary Note
- Trademarks
- Environmental Protection Statement
- Explanation of Symbols
- For Your Safety
- Two Year Warranty
- Table of Contents
- 1. Using the Command-Line Interface
- 2. Switching Commands
- 2.1 Port Configuration Commands
- 2.2 Spanning Tree Protocol (STP) Commands
- 2.2.1 spanning-tree
- 2.2.2 spanning-tree bpdumigrationcheck
- 2.2.3 spanning-tree configuration name
- 2.2.4 spanning-tree configuration revision
- 2.2.5 spanning-tree edgeport
- 2.2.6 spanning-tree forceversion
- 2.2.7 spanning-tree forward-time
- 2.2.8 spanning-tree hello-time
- 2.2.9 spanning-tree max-age
- 2.2.10 spanning-tree max-hops
- 2.2.11 spanning-tree mst
- 2.2.12 spanning-tree mst instance
- 2.2.13 spanning-tree mst priority
- 2.2.14 spanning-tree mst vlan
- 2.2.15 spanning-tree port mode
- 2.2.16 spanning-tree port mode all
- 2.2.17 show spanning-tree
- 2.2.18 show spanning-tree brief
- 2.2.19 show spanning-tree interface
- 2.2.20 show spanning-tree mst port detailed
- 2.2.21 show spanning-tree mst port summary
- 2.2.22 show spanning-tree mst summary
- 2.2.23 show spanning-tree summary
- 2.2.24 show spanning-tree vlan
- 2.3 VLAN Commands
- 2.3.1 vlan database
- 2.3.2 network mgmt_vlan
- 2.3.3 vlan
- 2.3.4 vlan acceptframe
- 2.3.5 vlan ingressfilter
- 2.3.6 vlan makestatic
- 2.3.7 vlan name
- 2.3.8 vlan participation
- 2.3.9 vlan participation all
- 2.3.10 vlan port acceptframe all
- 2.3.11 vlan port ingressfilter all
- 2.3.12 vlan port pvid all
- 2.3.13 vlan port tagging all
- 2.3.14 vlan protocol group
- 2.3.15 vlan protocol group add protocol
- 2.3.16 vlan protocol group remove
- 2.3.17 protocol group
- 2.3.18 protocol vlan group
- 2.3.19 protocol vlan group all
- 2.3.20 vlan pvid
- 2.3.21 vlan tagging
- 2.3.22 vlan association subnet
- 2.3.23 vlan association mac
- 2.3.24 show vlan
- 2.3.25 show vlan brief
- 2.3.26 show vlan port
- 2.3.27 show vlan association subnet
- 2.3.28 show vlan association mac
- 2.4 Double VLAN Commands
- 2.5 Provisioning (IEEE 802.1p) Commands
- 2.6 Protected Ports Commands
- 2.7 GARP Commands
- 2.8 GVRP Commands
- 2.9 GMRP Commands
- 2.10 Port-Based Network Access Control Commands
- 2.10.1 authentication login
- 2.10.2 clear dot1x statistics
- 2.10.3 clear radius statistics
- 2.10.4 dot1x defaultlogin
- 2.10.5 dot1x initialize
- 2.10.6 dot1x login
- 2.10.7 dot1x max-req
- 2.10.8 dot1x port-control
- 2.10.9 dot1x port-control all
- 2.10.10 dot1x re-authenticate
- 2.10.11 dot1x re-authentication
- 2.10.12 dot1x system-auth-control
- 2.10.13 dot1x timeout
- 2.10.14 dot1x user
- 2.10.15 users defaultlogin
- 2.10.16 users login
- 2.10.17 show authentication
- 2.10.18 show authentication users
- 2.10.19 show dot1x
- 2.10.20 show dot1x users
- 2.10.21 show users authentication
- 2.11 Storm-Control Commands
- 2.11.1 storm-control broadcast
- 2.11.2 storm-control broadcast level
- 2.11.3 storm-control broadcast all
- 2.11.4 storm-control broadcast all level
- 2.11.5 storm-control multicast
- 2.11.6 storm-control multicast level
- 2.11.7 storm-control multicast all
- 2.11.8 storm-control multicast all level
- 2.11.9 storm-control unicast
- 2.11.10 storm-control unicast level
- 2.11.11 storm-control unicast all
- 2.11.12 storm-control unicast all level
- 2.11.13 storm-control flowcontrol
- 2.11.14 show storm-control
- 2.12 Port-Channel/LAG (802.3ad) Commands
- 2.12.1 port-channel
- 2.12.2 addport
- 2.12.3 deleteport (Interface Config)
- 2.12.4 deleteport (Global Config)
- 2.12.5 port-channel static
- 2.12.6 port lacpmode
- 2.12.7 port lacpmode all
- 2.12.8 port-channel adminmode
- 2.12.9 port-channel linktrap
- 2.12.10 port-channel name
- 2.12.11 show port-channel brief
- 2.12.12 show port-channel
- 2.13 Port Mirroring
- 2.14 Static MAC Filtering
- 2.15 IGMP Snooping Configuration Commands
- 2.15.1 set igmp
- 2.15.2 set igmp interfacemode
- 2.15.3 set igmp fast-leave
- 2.15.4 set igmp groupmembership-interval
- 2.15.5 set igmp maxresponse
- 2.15.6 set igmp mcrtexpiretime
- 2.15.7 set igmp mrouter
- 2.15.8 set igmp mrouter interface
- 2.15.9 show igmpsnooping
- 2.15.10 show igmpsnooping mrouter interface
- 2.15.11 show igmpsnooping mrouter vlan
- 2.15.12 show mac-address-table igmpsnooping
- 2.16 Port Security Commands
- 2.17 LLDP (802.1AB) Commands
- 2.17.1 lldp transmit
- 2.17.2 lldp receive
- 2.17.3 lldp timers
- 2.17.4 lldp transmit-tlv
- 2.17.5 lldp transmit-mgmt
- 2.17.6 lldp notification
- 2.17.7 lldp notification-interval
- 2.17.8 clear lldp statistics
- 2.17.9 clear lldp remote-data
- 2.17.10 show lldp
- 2.17.11 show lldp interface
- 2.17.12 show lldp statistics
- 2.17.13 show lldp remote-device
- 2.17.14 show lldp remote-device detail
- 2.17.15 show lldp local-device
- 2.17.16 show lldp local-device detail
- 2.18 Denial of Service Commands
- 2.19 MAC Database Commands
- 3. Routing Commands
- 3.1 Address Resolution Protocol (ARP) Commands
- 3.2 IP Routing Commands
- 3.2.1 routing
- 3.2.2 ip routing
- 3.2.3 ip address
- 3.2.4 ip route
- 3.2.5 ip route default
- 3.2.6 ip route distance
- 3.2.7 ip forwarding
- 3.2.8 ip netdirbcast
- 3.2.9 ip mtu
- 3.2.10 encapsulation
- 3.2.11 show ip brief
- 3.2.12 show ip interface
- 3.2.13 show ip interface brief
- 3.2.14 show ip route
- 3.2.15 show ip route summary
- 3.2.16 show ip route preferences
- 3.2.17 show ip stats
- 3.3 Router Discovery Protocol Commands
- 3.4 Virtual LAN Routing Commands
- 3.5 Virtual Router Redundancy Protocol Commands
- 3.6 DHCP and BOOTP Relay Commands
- 3.7 Open Shortest Path First (OSPF) Commands
- 3.7.1 router ospf
- 3.7.2 enable (OSPF)
- 3.7.3 ip ospf
- 3.7.4 1583compatibility
- 3.7.5 area default-cost (OSPF)
- 3.7.6 area nssa (OSPF)
- 3.7.7 area nssa default-info-originate (OSPF)
- 3.7.8 area nssa no-redistribute (OSPF)
- 3.7.9 area nssa no-summary (OSPF)
- 3.7.10 area nssa translator-role (OSPF)
- 3.7.11 area nssa translator-stab-intv (OSPF)
- 3.7.12 area range (OSPF)
- 3.7.13 area stub (OSPF)
- 3.7.14 area stub no-summary (OSPF)
- 3.7.15 area virtual-link (OSPF)
- 3.7.16 area virtual-link authentication
- 3.7.17 area virtual-link dead-interval (OSPF)
- 3.7.18 area virtual-link hello-interval (OSPF)
- 3.7.19 area virtual-link retransmit-interval (OSPF)
- 3.7.20 area virtual-link transmit-delay (OSPF)
- 3.7.21 default-information originate (OSPF)
- 3.7.22 default-metric (OSPF)
- 3.7.23 distance ospf (OSPF)
- 3.7.24 distribute-list out (OSPF)
- 3.7.25 exit-overflow-interval (OSPF)
- 3.7.26 external-lsdb-limit (OSPF)
- 3.7.27 ip ospf areaid
- 3.7.28 ip ospf authentication
- 3.7.29 ip ospf cost
- 3.7.30 ip ospf dead-interval
- 3.7.31 ip ospf hello-interval
- 3.7.32 ip ospf priority
- 3.7.33 ip ospf retransmit-interval
- 3.7.34 ip ospf transmit-delay
- 3.7.35 ip ospf mtu-ignore
- 3.7.36 router-id (OSPF)
- 3.7.37 redistribute (OSPF)
- 3.7.38 maximum-paths (OSPF)
- 3.7.39 timers spf
- 3.7.40 trapflags (OSPF)
- 3.7.41 show ip ospf
- 3.7.42 show ip ospf area
- 3.7.43 show ip ospf border-routers
- 3.7.44 show ip ospf database
- 3.7.45 show ip ospf database database-summary
- 3.7.46 show ip ospf interface
- 3.7.47 show ip ospf interface brief
- 3.7.48 show ip ospf interface stats
- 3.7.49 show ip ospf neighbor
- 3.7.50 show ip ospf range
- 3.7.51 show ip ospf statistics
- 3.7.52 show ip ospf stub table
- 3.7.53 show ip ospf virtual-link
- 3.7.54 show ip ospf virtual-link brief
- 3.8 Routing Information Protocol (RIP) Commands
- 3.8.1 router rip
- 3.8.2 enable (RIP)
- 3.8.3 ip rip
- 3.8.4 auto-summary
- 3.8.5 default-information originate (RIP)
- 3.8.6 default-metric (RIP)
- 3.8.7 distance rip
- 3.8.8 distribute-list out (RIP)
- 3.8.9 ip rip authentication
- 3.8.10 ip rip receive version
- 3.8.11 ip rip send version
- 3.8.12 hostroutesaccept
- 3.8.13 split-horizon
- 3.8.14 redistribute (RIP)
- 3.8.15 show ip rip
- 3.8.16 show ip rip interface brief
- 3.8.17 show ip rip interface
- 4. Quality of Service (QoS) Commands
- 4.1 Class of Service (CoS) Commands
- 4.1.1 classofservice dot1p-mapping
- 4.1.2 classofservice ip-precedence-mapping
- 4.1.3 classofservice ip-dscp-mapping
- 4.1.4 classofservice trust
- 4.1.5 cos-queue min-bandwidth
- 4.1.6 cos-queue strict
- 4.1.7 traffic-shape
- 4.1.8 show classofservice dot1p-mapping
- 4.1.9 show classofservice ip-precedence-mapping
- 4.1.10 show classofservice ip-dscp-mapping
- 4.1.11 show classofservice trust
- 4.1.12 show interfaces cos-queue
- 4.2 Differentiated Services (DiffServ) Commands
- 4.3 DiffServ Class Commands
- 4.3.1 class-map
- 4.3.2 class-map rename
- 4.3.3 match ethertype
- 4.3.4 match any
- 4.3.5 match class-map
- 4.3.6 match cos
- 4.3.7 match secondary-cos
- 4.3.8 match destination-address mac
- 4.3.9 match dstip
- 4.3.10 match dstl4port
- 4.3.11 match ip dscp
- 4.3.12 match ip precedence
- 4.3.13 match ip tos
- 4.3.14 match protocol
- 4.3.15 match source-address mac
- 4.3.16 match srcip
- 4.3.17 match srcl4port
- 4.3.18 match vlan
- 4.3.19 match secondary-vlan
- 4.4 DiffServ Policy Commands
- 4.5 DiffServ Service Commands
- 4.6 DiffServ Show Commands
- 4.7 MAC Access Control List (ACL) Commands
- 4.8 IP Access Control List (ACL) Commands
- 4.1 Class of Service (CoS) Commands
- 5. Utility Commands
- 5.1 Commands for accessing base/extension fabric
- 5.2 Commands for download and startup Configuration
- 5.3 ATCA commands
- 5.4 System Information and Statistics Commands
- 5.4.1 show arp switch
- 5.4.2 show eventlog
- 5.4.3 show hardware
- 5.4.4 show version
- 5.4.5 show interface
- 5.4.6 show interface ethernet
- 5.4.7 show mac-addr-table
- 5.4.8 show running-config
- 5.4.9 show sysinfo
- 5.4.10 show tech-support
- 5.4.11 show boardinfo post-status
- 5.4.12 show boardinfo sensors
- 5.4.13 show boardinfo event-log
- 5.4.14 show boardinfo update-status
- 5.4.15 show boardinfo version
- 5.4.16 show boardinfo address
- 5.4.17 show boardinfo fru
- 5.4.18 show boardinfo ipmidev
- 5.4.19 show boardinfo led
- 5.4.20 show boardinfo amc connection
- 5.4.21 show boardinfo amc fru
- 5.4.22 show boardinfo fcap
- 5.4.23 show boardinfo routing
- 5.4.24 show boardinfo xfp
- 5.5 Logging Commands
- 5.6 System Utility and Clear Commands
- 5.7 Keying for Advanced Features
- 5.8 Simple Network Time Protocol (SNTP) Commands
- 5.8.1 sntp broadcast client poll-interval
- 5.8.2 sntp client mode
- 5.8.3 sntp client port
- 5.8.4 sntp unicast client poll-interval
- 5.8.5 sntp unicast client poll-timeout
- 5.8.6 sntp unicast client poll-retry
- 5.8.7 sntp multicast client poll-interval
- 5.8.8 sntp server
- 5.8.9 show sntp
- 5.8.10 show sntp client
- 5.8.11 show sntp server
- 5.9 DHCP Server Commands
- 5.9.1 ip dhcp pool
- 5.9.2 client-identifier
- 5.9.3 client-name
- 5.9.4 default-router
- 5.9.5 dns-server
- 5.9.6 hardware-address
- 5.9.7 host
- 5.9.8 lease
- 5.9.9 network (DHCP Pool Config)
- 5.9.10 bootfile
- 5.9.11 domain-name
- 5.9.12 netbios-name-server
- 5.9.13 netbios-node-type
- 5.9.14 next-server
- 5.9.15 option
- 5.9.16 ip dhcp excluded-address
- 5.9.17 ip dhcp ping packets
- 5.9.18 service dhcp
- 5.9.19 ip dhcp bootp automatic
- 5.9.20 ip dhcp conflict logging
- 5.9.21 clear ip dhcp binding
- 5.9.22 clear ip dhcp server statistics
- 5.9.23 clear ip dhcp conflict
- 5.9.24 show ip dhcp binding
- 5.9.25 show ip dhcp global configuration
- 5.9.26 show ip dhcp pool configuration
- 5.9.27 show ip dhcp server statistics
- 5.9.28 show ip dhcp conflict
- 5.10 DHCP Filtering
- 6. Management Commands
- 6.1 Network Interface Commands
- 6.2 Console Port Access Commands
- 6.3 Telnet Commands
- 6.4 Secure Shell (SSH) Command
- 6.5 User Account Commands
- 6.6 SNMP Commands
- 6.6.1 snmp-server
- 6.6.2 snmp-server bind
- 6.6.3 snmp-server community
- 6.6.4 snmp-server community ipaddr
- 6.6.5 snmp-server community ipmask
- 6.6.6 snmp-server community mode
- 6.6.7 snmp-server community ro
- 6.6.8 snmp-server community rw
- 6.6.9 snmp-server enable traps violation
- 6.6.10 snmp-server enable traps
- 6.6.11 snmp-server enable traps bcaststorm
- 6.6.12 snmp-server enable traps linkmode
- 6.6.13 snmp-server enable traps multiusers
- 6.6.14 snmp-server enable traps stpmode
- 6.6.15 snmptrap
- 6.6.16 snmptrap snmpversion
- 6.6.17 snmptrap ipaddr
- 6.6.18 snmptrap mode
- 6.6.19 snmp trap link-status
- 6.6.20 snmp trap link-status all
- 6.6.21 show snmpbind
- 6.6.22 show snmpcommunity
- 6.6.23 show snmptrap
- 6.6.24 show trapflags
- 6.7 CLI Command Logging Command
- 6.8 RADIUS Commands
- 6.9 TACACS+ Commands
- 6.10 Configuration Scripting Commands
- 6.11 Pre-login Banner and System Prompt Commands
- 6.12 Bootcycle commands
- 6.13 Watchdog support
- 6.14 ASI commands
- A. Getting Help
- A. Table of Contents