Rockwell Automation 1336T PLC Comm. Adapter, Series B, FRN 2.xx-3.xx - Manual (Page 269)

Publication 1336 FORCE–5.13 –– September, 1998
A
address selection, 2–5
All Info, 7–65
Allen–Bradley, P–7
contacting for assistance, P–7
analog I/O
Analog In 1 Offset parameter, 6–31
Analog In 1 parameter, 6–20
Analog In 1 Scale parameter, 6–31
Analog In 2 Offset parameter, 6–31
Analog In 2 parameter, 6–20
Analog In 2 Scale parameter, 6–32
Analog In 3 Offset parameter, 6–32
Analog In 3 parameter, 6–20
Analog In 3 Scale parameter, 6–32
Analog In 4 Offset parameter, 6–32
Analog In 4 parameter, 6–21
Analog In 4 Scale parameter, 6–33
Analog Out 1 Offset parameter, 6–33
Analog Out 1 parameter, 6–30
Analog Out 1 Scale parameter, 6–33
Analog Out 2 Offset parameter, 6–33
Analog Out 2 parameter, 6–30
Analog Out 2 Scale parameter, 6–34
Analog Out 3 Offset parameter, 6–34
Analog Out 3 parameter, 6–30
Analog Out 3 Scale parameter, 6–34
Analog Out 4 Offset, 6–34
Analog Out 4 parameter, 6–30
Analog Out 4 Scale parameter, 6–35
connections (TB21), 1–6
parameters, 2–9– 2–13
setting up the SCANport parameters,
5–10
SP Analog In parameter, 6–20
SP Analog Out parameter, 6–30
SP Analog Sel parameter, 6–31
B
baud rate selection, 2–2
block transfer
examples of, 3–15
explanation of, 7–1
status word, 7–2
transferring data, 3–10
BRAM
enable/disable, 1–3
functions, 6–1
BRAM Save, Recall, Initialize, 7–27
C
cable specifications for port wiring, 1–8
channel, choosing for control, 6–40
channel A
ChA Fault Sts parameter, 6–43
ChA RIO Flt Sel parameter, 6–38
ChA RIO Warn Sel parameter, 6–39
ChA RIOS Retries parameter, 6–40
ChA Warn Sts parameter, 6–44
displaying current DIP switch settings,
6–12
displaying current LED state, 6–12
logic command parameter, 6–27
remote I/O input parameters, 6–15– 6–17
remote I/O output parameters, 6–22–
6–24
channel B
ChB Fault Sts parameter, 6–44
ChB RIO Flt Sel, 6–41
ChB RIO Warn Sel parameter, 6–42
ChB RIOS Retries parameter, 6–43
ChB Warn Sts parameter, 6–45
displaying current DIP switch settings,
6–12
displaying current LED state, 6–13
logic command parameter, 6–27
remote I/O input parameters, 6–17– 6–20
remote I/O output parameters, 6–25–
6–26
Clear Run Time Accumulator, 7–50
communications configuration, 1–8– 1–12
DH+ configuration, 1–11
RIO configruation, 1–8– 1–10
contacting Allen–Bradley for assistance, P–7
contents of manual, P–2
Continuous Parameter Link Read, 7–30
Continuous Parameter Link Write, 7–35
Continuous Parameter Value Read, 7–6
Continuous Parameter Value Write, 7–14
continuous trends, 9–8
D
data sample rate for trending, 9–7
definitions, P–4
DH+
channel configuration, 1–11
Index