ETC Unison Paradigm ACP Configuration Manual v2.1.2 User Manual
Page 82
77
Paradigm Architectural Control Processor Configuration Manual
D
D
A
A
A
Note:
Note:
Note:
Note:
Note:
Note:
Note:
Note:
Note:
Note:
Note:
A D
Note:
Note:
Emergency Dimmers
1:
O n
2: O n
3: --
4: O n
5: --
6: --
7: O n
8: O n
9: O n
1 0: --
11: O n
1 2: O n
13: N A
1 4: N A 1 5 A : O n
1 5 B:O n 1 6 A :O n 1 6 B:
O n
On is default,
-- =off, NA =dimmer that
is not applicable such as a
CC20 or single density dimmer.
Dimmer doubled dimmers have
“a”&“b” dimmers. Use [and]
and [thru] functions
to select.
Emergency Dimmers
Emergency Level:
100
Load Shedding:
On
Input Type:
Maintained
Active When:
Closed
Emergency Setup
Dimming Setup
Dimmer Setup
Patch By DMX Start
Patch Dimmers
Emergency Setup
Quick Rack Setup
Push to Set Levels
Patch Dimmers
Mode: Dim:
DMX
DMX
1:
111
DD 2:
112a 368b
3: NA
4: 113
HiRes 5:
114H
115L
DD 6:
116a 117b
Edits all
patch data including
patch set in “Patch by DMX
Start”. Use [and] and [thru]
functions to select dimmers.
Dimmers with less than 2
controllable channels
display NA.
Dimming Setup
Dimmer Setup
Patch By DMX Start
Patch Dimmers
Emergency Setup
Quick Rack Setup
Push to Set Levels
Patch by DMX Start
Dimmer 1 Start:
111
Dimmer 24 End:
135
Patches all dimmers
sequentially with a
DMX start address.
End is info only.
Dimmer 1 Start:
is the only editable
field. Dimmer doubled dimmers
are applied a default +256
offset although the end
value does not reflect
the DD adjustment.
Patch by DMX Start
Dimmer 1 Start:
111
Dimmer 24 End:
135
Patches all dimmers
sequentially with a
DMX start address.
End is info only.
Dimming Setup
Dimmer Setup
Patch By DMX Start
Patch Dimmers
Emergency Setup
Quick Rack Setup
Push to Set Levels
Dimmer Setup
From Dimmer:
1 to: 1
Module Type:
D20
Mode:
Normal
Curve:
Mod
Square
Threshold: 1%
Voltage Reg:
On
Max
Scale:
118V
Min Scale: 6V
Dyn Preheat:
Off
Transformer mode:
On
DMX Res:
Lo 8 bit
The available
module type list is
rack voltage dependant.
Changing a module type
defaults all properties for
the specified dimmer(s)
(mode, curve, etc).
Dimmer Setup
From Dimmer:
1 to: 1
Module Type:
D20
Mode:
Normal
Curve:
Mod
Square
Threshold: 1%
Voltage Reg:
On
Max
Scale:
118V
Min Scale: 6V
Dyn Preheat:
Off
Transformer mode:
On
DMX Res:
Lo 8 bit
Dimmer Setup
From Dimmer:
1
to: 1
Module Type:
D20
Mode:
Normal
Curve:
Mod
Square
Threshold: 1%
Voltage Reg:
On
Max
Scale:
118V
Specify a
range of dimmers for
dimmer setup. When a range
of dimmers is selected, those
properties that are not equal
display as blank. Edits made
to empty property apply
to all applicable.
Dimmer Setup
From Dimmer:
1 to: 1
Module Type:
D20
Mode:
Normal
Curve:
Mod
Square
Threshold: 1%
Voltage Reg:
On
Max
Scale:
118V
Min Scale: 6V
Dyn Preheat:
Off
Transformer mode:
On
DMX Res:
Lo 8 bit
Dimming Setup
Dimmer Setup
Patch By DMX Start
Patch Dimmers
Emergency Setup
Quick Rack Setup
Push to Set Levels
To identify push
[####-####-####]
[###.###.###.###]
[####-####-####]
[####-####-####]
[###.###.###.###]
[###.###.###.###]
Found w/Error
Lists all
devices that have been
discovered but cannot be
connected/bound because of
neuron status or
communication error. Send a
“Wink” command by
pressing
Space:
Found:
####
Needed:
####
Connected: ####
Unconnected: ####
Found w/Error:
####
Stations & LonWorks
To identify push
Heritage 5 btn
[####-####-####]
LCD 7”
[####-####-####]
LightSensor Type 1
[####-####-####]
Lists all
unconnected devices &
their defined type.
Send a “Wink” command by
pressing
Space:
Found:
####
Needed:
####
Connected: ####
Unconnected
: ####
Found w/Error:
####
Stations & LonWorks
Lists all
connected devices and
their configured name.
Send a “Wink” command by
pressing
To identify push
House
Master
[####-####-####]
Presets
1
[####-####-####]
Daylight
1
[####-####-####]
Stations & LonWorks
Space:
Found:
####
Needed:
####
Connected:
####
Unconnected: ####
Found w/Error:
####
20 gang Station A
Custom
Presets 3
Heritage 5 btn
FOH LCD
LCD 7”
Heritage 4fdr 7btn
Needed
Lists all
Light Designer
configured station
devices by their configured
name and defined type.
Stations & LonWorks
Space:
Found:
####
Needed
:
####
Connected: ####
Unconnected: ####
Found w/Error:
####
To identify push
Heritage 5 btn
[####-####-####]
LCD 7”
[###.###.###.###]
Light Sensor Type1
[####-####-####]
Lists all
found or discovered
devices and their defined
types for the processor.
Stations & LonWorks
Space:
Found:
####
Needed:
####
Connected: ####
Unconnected: ####
Found w/Error:
####
Stations & LonWorks
Space:
Found:
####
Needed:
####
Connected: ####
Unconnected: ####
Found w/Error:
####
All spaces for the
selected processor
display in alphabetical
order.
1 About Dimmer
2 DMX Level Data
3 Version Info
4 Project Information
5 Statistics
6 View Message Log
7 System Network
About
8 Stations and LonWorks
System Network
Processor 1
10.101.10.101
Manual
*Local*
Processor 2
10.101.10.102
Auto Online
LCD FOH 1
The (read
only) system network
statistics menu provides
online status of the Paradigm
system, Ethernet communi-
cation properties and
connected Paradigm LCD’s
on Ethernet
1 About Dimmer
2 DMX Level Data
3 Version Info
4 Project Information
5 Statistics
6 View Message Log
7 System Network
8 Stations and LonWorks
View Message Log
01:00:00
7/01/08
ACP Online
00:59:45
07/01/08
v1.2.3
upgrade
00:58:15
07/01/08
Dim soft ver error
00:57:00
07/01/08
The read only
message log is intended
to give users a
way to see logged data
without extracting the log
file. Up to 100 of the
most recent messages
display.
About
1 About Dimmer
2 DMX Level Data
3 Version Info
4 Project Information
5 Statistics
6 View Message Log
7 System Network
8 Stations and LonWorks
About
Main Menu
1 About
2 Dimming Setup
3 Arch Setup
4 Dimming Control
5 Arch Control
6 File Operations
7 View/Clear Errors
8 Restricted Access
9 Timed Event Setup
Select Space
(abc)
Entry
Space 1
Space 2
Space 3
Found
Connected
Unconnected