Gradall 534C-6 Parts Manual - Manual (Page 44)

2-2
NOTE #1: When 9108-1384 Pivot Pin breaks, order part number 9108-5077 Steer
Cylinder Pivot Block Kit for the replacement parts needed to accommodate new pivot pins.
NOTE #2: Cylinder base end must be free to rotate. Shim steer cylinder base end as required to maintain a total max.
gap of 1/16".
NOTE #3: Shim bottom knuckles as required to maintain no more than 1/32" movement. Shim top knuckles as required
to maintain no more than 1/16" gap. Must have a minimum of one shim.
NOTE #4: All machines need to bore Steering Knuckles to use items 62 & 63. See diagram on previous page. Unless you
have purchased new Steering Knuckles part number, 9112-0003 & 9112-0004.
NOTE #5: You may have to use item 37 in place of items 28 & 64 unless you have purchased new Steering Knuckles part
number, 9112-0003 & 9112-0004. See engineering print that comes with the Steering Knuckle Kit for details.
NOTE #6: See option section for details on the Rear Axle Rework Kit and the Rear Axle Advantage Kit.
Item Part No. Qty. Description Of Part
26 9108-1415 2 DIRT SHIELD
27 9104-1732 2 SPACER
28 8852-1208 2 HEX LOCKNUT, 1/2-13, (see note #5)
29 9104-1481 2 STEERING CYLINDER PIN
30 9104-1459 2 WASHER
31 8850-1416 2 HEX JAM NUT, 1-14, (torque to
225-250 ft.lbs.)
32 9108-1693 2 UPPER KING PIN
33 9112-3030 2 BACK-UP RING
34 8859-1032 2 O-RING
35 9112-3028 2 BUSHING
36 8692-1268 2 LIP SEAL
37 8821-1117 2 SOCKET HD CAPSCREW,
1/2-13X4-1/2, GR8
8855-1109 2 LOCKWASHER, 1/2, (see note #5)
38 9104-1439 2 TIE ROD PIN
39 8320-1140 2 HEX HD CAPSCREW, 3/8-16X2-3/4,
GR8
40 8852-1306 2 LOCKNUT, 3/8-16
41 9114-1424 2 LOWER KING PIN
42 9104-1449 2 SHIM, (.060 thick, see note #2)
43 9104-1450 2 SHIM, (.0478 thick, see note #2)
44 9104-1451 6 SHIM, (.106 thick, see note #2)
45 9112-3030 2 BACK-UP RING
46 8859-1032 2 O-RING
47 9112-3027 2 BUSHING
48 9112-3029 2 O-RING
49 8859-1104 4 O-RING
50 9112-1091 2 THRUST BUSHING
51 8821-2321 2 SOCKET HD CAPSCREW,
5/8-11X3-3/4, GR8
52 8855-1153 2 LOCKWASHER, 5/8
53 8867-1001 4 LUBE FITTING, STRAIGHT, 1/8
54 8867-1022 6 LUBE FITTING, 30 DEGREES, 1/8
55 8867-1033 4 LUBE FITTING, STRAIGHT, 1/4-28
56 8858-1323 4 RETAINING RING
57 8859-1019 2 O-RING
58 9104-1596 4 SHIM, (20 gauge, see note #2)
59 9103-1009 1 SHIM, (.0500 thick)
60 9108-1691 1 SHIM, (.1046 thick)
61 9020-6846 1 SHIM, (.1345 thick)
62 9112-1239 2 BUSHING, (see note #4)
63 9112-1240 4 BUSHING, (see note #4)
64 8821-1121 2 SOCKET HD CAPSCREW,
1/2-13X6-1/2, (see note #5)
Item Part No. Qty. Description Of Part
9103-5240 Ref STEERING KNUCKLE KIT, (includes
items 26 thru 28; 32 thru 37; 41
thru 44; 47 thru 52; four of item 54; 56
thru 58, 62, 63, & 64 - one kit does both
sides)
9104-5152 Ref STEERING CYLINDER PIN KIT,
(includes one each of items 25, 26, 27,
29, 30, 31, 49, & 57 - one kit
needed for each side)
1 9116-6012 1 REAR AXLE, (includes items 11, 35,
& 47)
2 9108-1177 1 REAR AXLE PIN
3 9002-0247 1 HEX HD CAPSCREW, 1-1/4-7X6
4 8856-1119 1 FLAT WASHER, 1-1/4
5 8510-1098 1 HEX NUT, 1-1/4-7
6 2460-1570 2 LIP SEAL
7 2 DRIVE HUB, 534 ONLY, (see page 6-6
for details)
2 NON DRIVING HUB, 532 ONLY,
(See page 6-7 for details)
8 8821-2321 2 SOCKET HEAD CAPSCREW,
5/8-11X3-3/4, GR8
9 8850-1110 2 HEX NUT, 5/8-11
10 9104-3222 4 12 PT. SCREW, 3/4-10X2, (torque to
270-290 ft. lbs.)
11 9112-3031 2 BUSHING
12 8320-1006 12 HEX HD CAPSCREW, 3/4-10X2, (torque
to 270-290 ft. lbs.)
13 8668-1572 12 HARDENED WASHER, 3/4
14 9116-6063 1 TIE ROD, (includes item 15)
15 9104-3247 2 SELF ALIGNING BUSHING
16 9112-0003 1 L.H. STEERING KNUCKLE, (see
note #4)
17 9112-0004 1 R.H. STEERING KNUCKLE, (see
note #4)
18 2 STEERING CYLINDER ASSY, (see page
10-8 for details)
19 8820-1065 2 HEX HD CAPSCREW, 1/2-13X1, GR5
20 9108-1461 2 WASHER, 3/16"
21 9108-1384 2 STEERING CYLINDER PIVOT PIN, (see
note # 1)
22 9020-1918 2 SHIM, (10 gauge, see note #2)
23 8822-1701 2 SET SCREW, 3/8-16X1/2"
24 8855-1013 2 LOCKWASHER, 1/2
25 8852-1312 2 HEX LOCKNUT, 3/4-10, (torque to
160-175 ft. lbs.)
CHASSIS & ATTACHING PARTS
Rear Axle & Attaching Parts
Starting Serial No. 0188002
Original Issue 1-90
Revised 3-1-99
PCN 971313, 980724,
980730 - JH * Revised parts list, service notes and illustration.