AERCO ProtoNode Gateway Rev 3 (with external LEDs) - Manual (Page 3)

AERCO ProtoNode Gateway
User Manual
OMM-0080_0H AERCO International, Inc. • 100 Oritani Dr. • Blauvelt, NY 10913 Page 3 of 126
GF-129 Ph.: 800-526-0288 11/06/2014
TABLE OF CONTENTS
CHAPTER 1:
INTRODUCTION .................................................................................. 5
CHAPTER 2:
BACNET/LONWORKS SETUP FOR PROTONODE RER/LER .......... 7
2.1 INSTALLATION STEPS FOR THE CUSTOMER ...................................................................... 7
2.2 RECORD IDENTIFICATION DATA ............................................................................................ 7
2.3 MODBUS COM SETTINGS ON AERCO DEVICES (RER OR LER) ......................................... 8
2.3.1 Set Modbus COM Setting On All Devices Connected to the ProtoNode ................................................... 8
2.4 DIP SWITCH CONFIGURATION................................................................................................ 9
2.4.1 ProtoNode RER (DIP Switch A0–A7): Setting the MAC Address for BACnet MS/TP .................................. 9
2.4.2 ProtoNode RER: Setting the Device Instance (Node-ID) for BACnet MS/TP and BACnet/IP ..................... 9
2.4.3 ProtoNode RER: Setting the Node-ID for Metasys N2 and Modbus/TCP ................................................ 11
2.4.4 Setting the Serial Baud Rate (DIP Switch B0 – B3) for BACnet MS/TP ..................................................... 11
2.4.5 S0–S3 Bank DIP Switches to Select and Load Device Configuration Files ................................................ 12
CHAPTER 3:
INTERFACING PROTONODE TO DEVICES .................................... 15
3.1 PROTONODE RER SHOWING CONNECTION PORTS AND FEATURES ........................... 15
3.2 PROTONODE LER SHOWING CONNECTION PORTS AND FEATURES ............................ 16
3.3 WIRING CONNECTIONS TO PROTONODE RER AND PROTONODE LER ......................... 17
3.3.1 ProtoNode 6-Pin Phoenix Connector – Pin Outs to Modbus RTU Products ............................................ 17
3.3.2 Biasing the Modbus RS-485 Network ...................................................................................................... 17
3.3.3 End of Line Termination Switch for the Modbus RS-485 port on the ProtoNode ................................... 18
3.4 ACS/BMS II WIRING CONNECTIONS TO PROTONODE RER AND LER ............................ 19
3.5 MODULEX BCM CONNECTIONS ........................................................................................... 20
3.6 ECS CONNECTIONS ............................................................................................................... 20
3.7 C-MORE CONNECTIONS ........................................................................................................ 20
3.8 AERCO C-MORE CONTROLLER PMC BOARD DIP SWITCH SETTINGS ........................... 21
CHAPTER 4: ........................................................................................................... 23
4.1 WIRING PROTONODE RER TO RS-485 FIELD PROTOCOL (BACNET MS/TP OR
METASYS N2) .......................................................................................................................... 23
4.2 WIRING THE PROTONODE LER FIELD PORT TO A LONWORKS NETWORK .................. 24
4.3 POWER-UP OF PROTONODE RER OR PROTONODE LER ................................................ 24
4.4 COMMISSIONING PROTONODE LER ON A LONWORKS NETWORK ............................... 25
4.5 INSTRUCTIONS TO UPLOAD XIF FILE FROM PROTONODE LER USING FS GUI WEB
SERVER .................................................................................................................................... 25
4.6 COMMISSIONING PROTONODE FPC-N35 ON A LONWORKS NETWORK ....................... 26
4.7 INSTRUCTIONS TO UPLOAD XIF FILE FROM PROTONODE FPC-N35 USING
FIELDSERVER GUI WEB SERVER ........................................................................................ 26
CHAPTER 5:
CONNECT THE PROTONODE’S WEB GUI TO SETUP IP ADDRESS
FOR BACNET/IP* ..................................................................................... 28
5.1 CONNECT THE PC TO THE PROTONODE VIA THE ETHERNET PORT ............................. 28
5.2 USE THE PROTONODE WEB GUI TO CONNECT TO THE PROTONODE .......................... 29
5.3 SET IP ADDRESS FOR BACNET/IP AND MODBUS TCP ..................................................... 30
CHAPTER 6:
INSTALL AND RUN THE UTILITY SOFTWARE TO SETUP IP
ADDRESS FOR BACNET/IP USING RUINET ......................................... 32
6.1 CONNECT THE PC TO THE PROTONODE VIA THE ETHERNET PORT ............................. 32
6.2 CONNECT TO THE PROTONODE USING RUI (RUINET) ..................................................... 33