Cable charts, Runtime communication cables - to processors – Rockwell Automation 2711 Standard PanelView Operator Terminal User Manual User Manual
Page 178

178
Publication 2711-UM014G-EN-P - September 2008
Chapter 12 Terminal Connections
Cable Charts
Refer to the following charts for a summary of PanelView terminal
connections to controllers and network interface modules.
Runtime Communication Cables - to Processors
Protocol
PanelView Standard Comm Port Cables: PanelView to Processor
SLC-500, 5/01,
5/02
CH1 RJ45
(DH-485)
SLC-5/03, 5/04, 5/05
CH0 (9-pin RS-232)
(DF1 or DH-485)
SLC 5/03
CH1 (RJ45)
(DH-485)
SLC 5/04
CH1
(DH+)
SLC 5/05
CH1
(ENET)
DF1
xxx16
xxx17
xxx18
RS-232 (DF1) Comm Port (8-pin Mini
Din)
PanelView 300 Micro
2711-xxx18
N/A
1761-CBL-AP00
(0.5 m/1.5 ft)
1761-CBL-PM02
(2 m/6.5 ft)
2711-CBL-PM05
(5 m/16 ft)
2711-CBL-PM10
(10 m/32 ft)
N/A
N/A
N/A
RS-232 (DF1) Communication Port
(9-pin)
PanelView 300 - 1400
2711-xxx16, 2711-xxx17
N/A
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
N/A
N/A
N/A
DH-485
xxx2
xxx3
xxx5
xxx9
xxx19
RS-232 (DH-485) Comm Port (8-pin
Mini Din)
PanelView 300 Micro
2711-xxx19
use AIC+ Module
(1761-NET-AIC)
Connect to Port 1
or 2
1761-CBL-AP00
(0.5 m/1.5 ft)
1761-CBL-PM02
(2 m/6.5 ft)
2711-CBL-PM05
(5 m/16 ft)
2711-CBL-PM10
(10 m/32 ft)
use AIC+
Module
(1761-NET-AIC)
Connect to Port
1 or 2
N/A
N/A
RS-232 (DH-485) Communication
Port (9-pin)
PanelView 300 - 1400
2711-xxx5, 2711-xxx9
use AIC+ Module
(1761-NET-AIC)
Connect to Port 1
or 2
2711-NC13 (5 m/16 ft)
2711-NC14 (10 m/32 ft)
2706-NC13 (3 m/10 ft)
use AIC+
Module
(1761-NET-AIC)
Connect to Port
1 or 2
N/A
N/A
DH-485 Communication Port (RJ45)
PanelView 300 - 1400
2711-xxx2, 2711-xxx3
1747-C10
(2 m/6 ft)
1747-C11
(1 ft/0.3 m)
1747-C20
(6 m/20 ft)
use AIC+ Module
(1761-NET-AIC)
Connect to Port 3
1747-C10
(2 m/6 ft)
1747-C11
(1 ft/0.3 m)
1747-C20
(6 m/20 ft)
N/A
N/A