Rockwell Automation 1771-QDC, D17716.5.87(Passport) CLAMP AND EJECT MODE - Manual (Page 5)

Table of Contents
ii
Jog Your Machine 5Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter Objectives 5Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determine Initial Clamp and Ejector Jog Values 5Ć2 . . . . . . . . . . . . . .
Jog Your Machine 5Ć4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure Jogs for the Screw and Injection Cylinder 5Ć6 . . . . . . . . . . .
Select Command and Status Bits to Sequence
Machine Operation 6Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter Objectives 6Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assess Your Logic Requirements 6Ć1 . . . . . . . . . . . . . . . . . . . . . . . .
Use Bit Tables 6Ć2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter Objectives 7Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use Configuration Command Block Worksheets 7Ć2 . . . . . . . . . . . . . .
Procedure to Determine and Record Worksheet Values 7Ć24 . . . . . . . . .
Determine Bit Selections: Assign Module Outputs for
Your Control Valves 7Ć24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Select the Type of PID Algorithm 7Ć25 . . . . . . . . . . . . . . . . . . . . . . . . .
Determine Word Selections: Set ERC Values and Timer Presets 7Ć26 . .
Determine Unselected Valve SetĆoutput Values 7Ć28 . . . . . . . . . . . . . . .
Set your Accel/Decel Ramp Rates 7Ć31 . . . . . . . . . . . . . . . . . . . . . . . .
Determine SetĆoutput Values for End of Profiles 7Ć32 . . . . . . . . . . . . . .
Set Pressure Control Limits 7Ć33 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Velocity Control Limits 7Ć35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Profile Gain Constants and Pressure Alarm Setpoints 7Ć37 . . . . . . .
Enter and Download your Worksheet Values 7Ć38 . . . . . . . . . . . . . . . .
Load Initial Profile Values for Machine Tuning 8Ć1 . . . . . . . . . .
Chapter Objectives 8Ć1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Determine and Enter Setpoints for the Clamp Close Profile (CPC) 8Ć1 .
Determine Bit Selections for Worksheet 8ĆA 8Ć4 . . . . . . . . . . . . . . . . .
Determine Word Values for Worksheet 8ĆA 8Ć5 . . . . . . . . . . . . . . . . . .
Enter and Download Your Worksheet Values 8Ć7 . . . . . . . . . . . . . . . .
Determine and Enter Clamp Open Profile (OPC) 8Ć8 . . . . . . . . . . . . . .
Determine Bit Selections for Worksheet 8ĆB 8Ć10 . . . . . . . . . . . . . . . . .
Determine Word Values for Worksheet 8ĆB 8Ć11 . . . . . . . . . . . . . . . . . .
Enter and Download your Worksheet Values 8Ć13 . . . . . . . . . . . . . . . .
Determine and Enter Ejector Profile (EPC) 8Ć14 . . . . . . . . . . . . . . . . . .
Determine Bit Selections for Worksheet 8ĆC 8Ć16 . . . . . . . . . . . . . . . . .
Determine Word Values for Worksheet 8ĆC 8Ć19 . . . . . . . . . . . . . . . . . .
Enter and Download your Worksheet Values 8Ć22 . . . . . . . . . . . . . . . .