Brocade Multi-Service IronWare Multicast Configuration Guide (Supporting R05.6.00) User Manual
Page 75
Multi-Service IronWare Multicast Configuration Guide
63
53-1003032-02
Multicast Outgoing Interface (OIF) list optimization
1
L3 (HW) 1: e4/12(VL52)
Flags (0x7046c8e1)
sm=1 ssm=0 hw=1 fast=1 slow=0 leaf=0 prun=0 tag=1 needRte=0 msdp_adv=1
AgeSltMsk=00000008, FID: 0x800e MVID: 1 , RegPkt 0, AvgRate 11257 profile: none
3 (49.1.1.108, 229.0.0.2) in v49 (tag e4/9), Uptime 00:03:51 Rate 11257
Sparse Mode, RPT=0 SPT=1 Reg=0 L2Reg=1 RegSupp=0 RegProbe=0 LSrc=1 LRcv=1
Source is directly connected. RP 192.168.1.1
num_oifs = 1
immediate_oifs = 0, inherited_oifs = 1, blocked_oifs = 0
52,4/12(00:03:51/0) Flags:00000004
fast ports ethe 4/12
L3 (HW) 1: e4/12(VL52)
Flags (0x7046c8e1)
sm=1 ssm=0 hw=1 fast=1 slow=0 leaf=0 prun=0 tag=1 needRte=0 msdp_adv=1
AgeSltMsk=00000008, FID: 0x800e MVID: 1 , RegPkt 0, AvgRate 11257 profile: none
Number of matching entries: 3
Syntax: show ip pim mcache mvid mvid
The mvid variable allows you to display an entry that matches a specified mvid.
describes the output parameters of the show ip pim mcache mvid 1 command.
TABLE 17
Output parameters of the show ip pim mcache mvid 1 command
Field
Description
Total entries in mcache
Shows the total number of PIM mcache entries.
v
Shows the interface name.
tag e
Shows the VLAN tagged ethernet interface.
Uptime
Shows the entry uptime.
Rate
Shows the total packet count.
Sparse mode
Shows that the PIM sparse mode is enabled.
RPT
Sets the flag to 1, if the entry is on the RP tree, else sets the flag to 0.
SPT
Sets the flag to 1, if the entry is on the source tree, or else sets the flag to 0.
Reg
Sets the flag to 1, if the data registration is in progress, or else sets the flag to 0.
L2Reg
Sets the flag to 1, if the source is directly connected to the router, or else sets the flag
to 0.
RegSupp
Sets the flag to 1, if the register suppression timer is running, or else sets the flag to 0.
RegProbe
Sets the flag to 1, if the mcache entry is entering the register probing period, or else
sets the flag to 0.
LSrc
Sets the flag to 1, if the source is in a directly-connected interface, or else sets the flag
to 0.
LRcv
Sets the flag to 1, if the receiver is directly connected to the router, or else sets the flag
to 0.
RP
Show the IP address of the RP.
num_oifs
Show the count of the outgoing interfaces.
immediate_oifs
Show the local immediate outgoing interface of the mcache entry.
inherited_oifs
Shows the PIM Sparse mode inherited outgoing interfaces.
blocked_oifs
Show the PIM Sparse mode blocked outgoing interfaces.
Flags
Show the flags associated with the forward entry.