Brocade Multi-Service IronWare Multicast Configuration Guide (Supporting R05.6.00) - Manual (Page 185)

Multi-Service IronWare Multicast Configuration Guide 173
53-1003032-02
IPv6 PIM Sparse
2
Flags (0x00260480)
sm=1 ssm=0 hw=0 fast=0 slow=0 leaf=0 prun=0 tag=0 needRte=0 msdp_adv=0
AgeSltMsk=00000000, FID: NotReq MVID: NotReq, RegPkt 0 profile: 2
2 (2001:1:1:1::149:101, ff1e::1) in v149 (tag e4/9), Uptime 00:27:43 Rate 2284
Sparse Mode, RPT=0 SPT=1 Reg=0 L2Reg=1 RegSupp=0 RegProbe=0 LSrc=1 LRcv=1
Source is directly connected. RP 2005::192:168:1:1
num_oifs = 1
immediate_oifs = 0, inherited_oifs = 1, blocked_oifs = 0
152,4/12(00:27:05/0) Flags:00000004
fast ports ethe 4/12
L3 (HW) 1: e4/12(VL152)
Flags (0x604688e1)
sm=1 ssm=0 hw=1 fast=1 slow=0 leaf=0 prun=0 tag=1 needRte=0 msdp_adv=0
AgeSltMsk=00000008, FID: 0x800f MVID: 1 , RegPkt 0, AvgRate 2228 profile: 2
3 (*, ff1e::2) RP 2005::192:168:1:1, in NIL (NIL), Uptime 00:27:05
Sparse Mode, RPT=1 SPT=0 Reg=0 L2Reg=0 RegSupp=0 RegProbe=0 LSrc=0 LRcv=1
No upstream neighbor because RP 2005::192:168:1:1 is itself
num_oifs = 1
immediate_oifs = 1, inherited_oifs = 0, blocked_oifs = 0
152,4/12(00:27:05/0) Flags:00000004
slow ports ethe 4/12
L3 (SW) 1: e4/12(VL152)
Flags (0x00260480)
sm=1 ssm=0 hw=0 fast=0 slow=0 leaf=0 prun=0 tag=0 needRte=0 msdp_adv=0
AgeSltMsk=00000000, FID: NotReq MVID: NotReq, RegPkt 0 profile: 2
4 (2001:1:1:1::149:101, ff1e::2) in v149 (tag e4/9), Uptime 00:27:43 Rate 2284
Sparse Mode, RPT=0 SPT=1 Reg=0 L2Reg=1 RegSupp=0 RegProbe=0 LSrc=1 LRcv=1
Source is directly connected. RP 2005::192:168:1:1
num_oifs = 1
immediate_oifs = 0, inherited_oifs = 1, blocked_oifs = 0
152,4/12(00:27:05/0) Flags:00000004
fast ports ethe 4/12
L3 (HW) 1: e4/12(VL152)
Flags (0x604688e1)
sm=1 ssm=0 hw=1 fast=1 slow=0 leaf=0 prun=0 tag=1 needRte=0 msdp_adv=0
AgeSltMsk=00000008, FID: 0x8010 MVID: 1 , RegPkt 0, AvgRate 2228 profile: 2
Syntax: show ipv6 pim mcache [ multicast cache entries source/group address | multicast cache
ipv6-group-address]
Syntax: show ipv6 pim [vrf vrf-name] mcache
The vrf parameter allows you to display the IPv6 PIM multicast cache for the VRF instance
identified by the vrf-name variable.
Table 40 describes the output parameters of the show ipv6 pim vrf mcache command.
TABLE 40 Output parameters of the show ipv6 pim vrf mcache command
Field Description
Total entries in mcache Shows the total number of PIM mcache entries.
Uptime Shows the entry uptime.
Rate Shows the total packet count.
Sparse mode Shows that the PIM sparse mode is enabled.
RPT Sets the flag to 1, if the entry is on the RP tree, else sets the flag to 0.
SPT Sets the flag to 1, if the entry is on the source tree, or else sets the flag to 0.
Reg Sets the flag to 1, if the data registration is in progress, or else sets the flag to 0.