Yaskawa AC Drive P1000 Bypass Technical Manual - Manual (Page 387)

Serial Communication Fault Detection Selection .......................... 360
Serial Communications Baud Rate Select ................................... 359
Serial Communications Cable Connection Terminal (TB3) .. 290, 308, 357
Serial Communications Fault Time Select .................................. 360
Serial Communications Node Address Select .............................. 359
Serial Communications Protocol Select ..................................... 359
Serial Communications Receive to Transmit Wait Time.................. 360
Serial Communication Terminals...............................................48
Serial Communication Transmission Error ................................. 191
Setup Mode ........................................................................68
Shielded Twisted-Pair Cables ...................................................51
Simplified Setup Using the Quick Setting Group ............................68
Slave Address ................................................................... 314
Smoke Purge in Bypass ........................................................ 190
Smoke Purge in Drive.......................................................... 190
Soft Charge Bypass Relay Maintenance..................................... 265
Soft Charge Bypass Relay Maintenance Time.............................. 193
Soft Starter Speed Reference at Previous Fault............................. 262
Software No. (Flash) ........................................................... 262
Software No. (ROM) ........................................................... 262
Software version ..................................................................29
Speed Control Range ........................................................... 227
Speed Estimation Type Speed Search..........................................87
Speed Search ......................................................................83
Speed Search Deactivation Current ............................................88
Speed Search Deceleration Time ...............................................89
Speed Search Delay Time .......................................................89
Speed Search Detection Compensation Gain .................................89
Speed Search Method Selection ................................................90
Speed Search Restart Current Level............................................90
Speed Search Restart Detection Time..........................................90
Speed Search Selection at Start .................................................88
Speed Search Wait Time.........................................................90
Stall Prevention ........................................................... 128, 172
Stall Prevention Level during Acceleration ........................... 128, 250
Stall Prevention Level during Run ..................................... 130, 251
Stall Prevention Limit during Acceleration ........................... 129, 250
Stall Prevention Selection during Deceleration....................... 129, 251
Starting Torque.................................................................. 227
Stationary Auto-Tuning..........................................................77
Stationary Auto-Tuning for Line-to-Line Resistance ........................76
Status Display .....................................................................70
STo ............................................................................... 188
Stopping Method after Communication Error .............................. 125
Stopping Method Selection......................................................83
Storage Temperature .............................................................38
Supported Properties of Objects .............................................. 295
Surrounding Area .................................................................38
Swing PWM ..................................................................... 104
T
T/L3.................................................................................43
T1-03 ...............................................................................78
T1-04 ...............................................................................78
T1-05 ...............................................................................78
T1-06 ...............................................................................78
T1-07 .......................................................................... 78, 79
TdE ............................................................................... 188
Terminal A1 Bias Setting...................................................... 118
Terminal A1 Function Selection.............................................. 118
Terminal A1 Gain Setting ..................................................... 118
Terminal A1 Signal Level Selection ......................................... 117
Terminal A2 Bias Setting...................................................... 120
Terminal A2 Function Selection.............................................. 119
Terminal A2 Gain Setting ..................................................... 120
Terminal A2 Signal Level Selection ......................................... 119
Terminal A3 Bias Setting...................................................... 119
Terminal A3 Function Selection.............................................. 119
Terminal A3 Gain Setting ..................................................... 119
Terminal A3 Signal Level Selection ......................................... 119
Terminal Board ...................................................................33
Terminal Board Connection Error............................................ 177
Terminal Board Connector ......................................................33
Test Run....................................................................... 76, 79
TIM ............................................................................... 188
Time Data Error................................................................. 188
Time Not Set .................................................................... 188
Time to Continue Making Fault Restarts .................................... 251
Too Many Speed Search Restarts............................................. 188
Torque Compensation Gain ............................................. 104, 172
Torque Compensation Primary Delay Time ................................ 172
Torque Detection ............................................................... 122
Torque Detection Level 1................................................ 135, 252
Torque Detection Time 1 ................................................ 135, 252
Troubleshooting without Fault Display...................................... 204
TrPC .............................................................................. 195
Tuning Errors.................................................................... 173
Types of Alarms, Faults, and Errors ......................................... 173
Types of Auto-Tuning for Induction Motors..................................76
U
U/T1 ................................................................................43
U1-01 ............................................................................. 207
U1-07 ............................................................................. 205
UL3 ......................................................................... 188, 195
UL6 ......................................................................... 188, 195
UL and CSA Standards ........................................................ 337
UL Standards Compliance.......................................................43
Undertorque Detection 1................................................. 188, 195
Undertorque Detection 6....................................................... 195
Undertorque Detection Operation ............................................ 135
Undervoltage .................................................................... 195
Undervoltage 3 .................................................................. 189
Undervoltage 3 (Soft-Charge Circuit Fault)................................. 189
Undervoltage Detection Level (Uv1) .................................. 128, 250
Undervoltage Protection ....................................................... 227
Unexpected Noise from Connected Machinery............................. 208
Unit Code ........................................................................ 142
Up/Down Command Operation............................................... 116
Up Arrow Key.....................................................................59
User-Set Display Units Decimal Display.................................... 142
User-Set Display Units Maximum Value.................................... 142
Uv ................................................................................. 195
Uv1 ............................................................................... 189
Uv2 ............................................................................... 189
Uv3 ............................................................................... 189
V
V/f Characteristics .............................................................. 227
V/f Control.........................................................................27
Index
YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual 387