Yaskawa AC Drive P1000 Bypass Technical Manual - Manual (Page 175)

n Minor Faults and Alarms
Refer to Table 6.5 for an overview of possible alarm codes. Conditions such as overvoltages can trip faults and alarms. It is
important to distinguish between faults and alarms to determine the proper corrective actions.
When the drive detects an alarm, the ALM indicator LED blinks and the alarm code display flashes. A fault (not an alarm) is
present if the ALM LED lights without blinking. Refer to Faults on page 174 for information on fault codes.
Table 6.5 Minor Fault and Alarm Displays
HOA
Keypad
Display
Name Page
AL02 BAS Interlock Open 190
AL03 Smoke Purge in Bypass 190
AL04 Smoke Purge in Drive 190
AL13 Loss of Load 190
AL14 Serial Communications Fault 190
bAT HOA Keypad Battery Voltage Low 176
bb Drive Baseblock 191
bUS Option Card Communications Error 191
CE MEMOBUS/Modbus Communication Error 191
CrST Cannot Reset 192
EF Run Command Input Error 192
EF0 Option Card External Fault 192
FAn Internal Fan Fault 178
FbH Excessive PI Feedback 192
FbL PI Feedback Loss 192
Fn1 External Fan Fault 182
inTLK <1> Interlock Open 193
LT-1 Cooling Fan Maintenance Time 193
HOA
Keypad
Display
Name Page
LT-2 Capacitor Maintenance Time 193
LT-3 Soft Charge Bypass Relay Maintenance Time 193
oH Heatsink Overheat 194
oH2 Drive Overheat 194
oH3 Motor Overheat 194
oL3 Overtorque 1 194
ov Overvoltage 194
PASS MEMOBUS/Modbus Test Mode Complete 195
SAFE Customer Safety 195
SE MEMOBUS/Modbus Test Mode Fault 195
TdE Thermistor Disconnect 195
TIM Time Not Set 188
UL3 Undertorque 1 195
UL6 Undertorque 6 195
Uv Undervoltage 195
voF Output Voltage Detection Fault 196
WrUn Waiting for Run 196
<1> ALM LED will not blink.
n Operation Errors
Table 6.6 Operation Error Displays
HOA
Keypad
Display
Name Page
oPE01 Drive Unit Setting Error 197
oPE02 Parameter Setting Range Error 197
oPE03 Multi-Function Input Setting Error 197
oPE05 Run Command Selection Error 198
oPE07 Multi-Function Analog Input Selection Error 198
HOA
Keypad
Display
Name Page
oPE09 PI Control Selection Error 198
oPE10 V/f Data Setting Error 198
oPE11 Carrier Frequency Setting Error 198
oPE28 Sequence Timer Error 199
n Auto-Tuning Errors
Table 6.7 Auto-Tuning Error Displays
HOA
Keypad
Display
Name Page
End3 Rated Current Setting Alarm 200
End4 Adjusted Slip Value Fell Below Lower Limit 200
End5 Resistance Between Lines Error 200
End7 No-Load Current Alarm 200
Er-01 Motor Data Error 200
Er-02 Alarm 200
HOA
Keypad
Display
Name Page
Er-03 OFF Button Input 201
Er-04 Line-to-Line Resistance Error 201
Er-05 No-Load Current Error 201
Er-08 Rated Slip Error 201
Er-09 Acceleration Error 201
Er-12 Current Detection Error 201
6.3 Drive Alarms, Faults, and Errors
YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual 175
6
Diagnostics & Troubleshooting