beautypg.com

Z2: bypass control input/output – Yaskawa AC Drive P1000 Bypass Technical Manual User Manual

Page 270

background image

No.

(Addr.

Hex)

Name

LCD Display

Description

Values

Page

Z1-40

(85ED) Auto Transfer Wait

Time

Auto Xfer Wait T

If Auto Transfer is enabled and a drive fault is detected, the

bypass controller will wait this length of time before switching

to bypass.

Default: 0.0 s

Min.: 0.0

Max.: 300.0

161

<1> Values are given in Hz, but actual values are dependent upon unit settings using drive parameters o1-03, o1-09, o1-10, and o1-11.

u

Z2: Bypass Control Input/Output

No.

(Addr.

Hex)

Name

Description

Values

Page

Z2-01

(8563)

Digital Input 1 Function

Select

0: Unused (Available for Serial Comms)

3: DRV Multi-Function Input S3 (H1-03 Setting)

4: DRV Multi-Function Input S4 (H1-04 Setting)

5: DRV Multi-Function Input S5 (H1-05 Setting)

6: DRV Multi-Function Input S6 (H1-06 Setting)

7: DRV Multi-Function Input S7 (H1-07 Setting)

21: Run (AUTO Mode)

22: Run Enable (Safety)

23: Run Interlock (BAS)

24: Remote Transfer to Bypass

25: Smoke Purge Bypass Run to Destruction

26: Smoke Purge Drive Run to Destruction at Smoke Purge Preset Speed (See

Z1-10). Bypass controller will stay in this state even if the drive faults or is

unavailable.

27: Motor OR Select (2-Motor OR function; 0/1 for Motor 1/2. Behavior

defined by Z1-11)

28: Motor AND Select (2-Motor AND function; 0/1 for 1/2 motor. If 1 motor,

then look to Motor OR input for selected motor. Behavior defined by Z1-11)

29: Motor 1 Overload Contact. When input is open, declare an OL Fault, issue

an EF0 fault to the drive, delay per EF0 Fault Delay Time (Z1-30), and open

Drive Output (K2) and Bypass (K3) contactors.

30: Motor 2 Overload Contact. When input is open, declare an OL Fault, issue

an EF0 fault to the drive, delay per EF0 Fault Delay Time (Z130), and open

Drive Output (K2) and Bypass (K3) contactors.

31: HAND Select

32: AUTO Select

33: DRIVE/BYPASS Select (0/1 for Drive/Bypass)

34: Fault Reset

35: External Fault (EF0)

36: External Fault (EFB)

37: Run Reverse

Default: 21

Range: 0 to 36

161

Z2-02

(8564)

Digital Input 2 Function

Select

Default: 22

Range: 0 to 36

161

Z2-03

(8565)

Digital Input 3 Function

Select

Default: 23

Range: 0 to 36

161

Z2-04

(8566)

Digital Input 4 Function

Select

Default: 24

Range: 0 to 36

161

Z2-05

(8567)

Digital Input 5 Function

Select

Default: 25

Range: 0 to 36

161

Z2-06

(8568)

Digital Input 6 Function

Select

Default: 0

Range: 0 to 36

161

Z2-07

(8569)

Digital Input 7 Function

Select

Default: 0

Range: 0 to 36

161

Z2-08

(856A)

Digital Input 8 Function

Select

Default: 29

Range: 0 to 36

161

Z2-09

(856B)

Digital Input 1 Invert Select

0: Normal. Lack of input signal = OFF

1: Invert. Lack of input signal = ON

Default: 0

Range: 0, 1

163

Z2-10

(856C)

Digital Input 2 Invert Select

0: Normal. Lack of input signal = OFF

1: Invert. Lack of input signal = ON

Default: 1

Range: 0, 1

163

Z2-11

(856D)

Digital Input 3 Invert Select

0: Normal. Lack of input signal = OFF

1: Invert. Lack of input signal = ON

Default: 0

Range: 0, 1

163

Z2-12

(856E)

Digital Input 4 Invert Select

0: Normal. Lack of input signal = OFF

1: Invert. Lack of input signal = ON

Default: 0

Range: 0, 1

163

Z2-13

(856F)

Digital Input 5 Invert Select

0: Normal. Lack of input signal = OFF

1: Invert. Lack of input signal = ON

Default: 0

Range: 0, 1

163

B.14 Z: Bypass Parameters

270

YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual