Yaskawa AC Drive P1000 Bypass Technical Manual - Manual (Page 300)

Object ID Object Name
Modbus
Address
Active Text Inactive Text PV Access
BV69 BYP BYPASS Sel CMD 8400H: bit 12 BYP DRV C
BV70 BYP Fault Reset CMD 8400H: bit 13 ON OFF C
BV71 BYP Ext Fault CMD 8400H: bit 14 ON OFF C
BV72 BYP DI-01 Command 8402H: bit 0 ON OFF W
BV73 BYP DI-02 Command 8402H: bit 1 ON OFF W
BV74 BYP DI-03 Command 8402H: bit 2 ON OFF W
BV75 BYP DI-04 Command 8402H: bit 3 ON OFF W
BV76 BYP DI-05 Command 8402H: bit 4 ON OFF W
BV77 BYP DI-06 Command 8402H: bit 5 ON OFF W
BV78 BYP DI-07 Command 8402H: bit 6 ON OFF W
BV79 BYP DI-08 Command 8402H: bit 7 ON OFF W
BV80 BYP HAND Mode Status 8784H: bit 0 ON OFF R
BV81 BYP OFF Mode Status 8784H: bit 1 ON OFF R
BV82 BYP AUTO Mode Status 8784H: bit 2 ON OFF R
BV83 BYP DRV Mode Status 8784H: bit 3 ON OFF R
BV84 BYP BYPASS Mode Stat 8784H: bit 4 ON OFF R
BV85 BYP Smk Prg BYP Stat 8784H: bit 5 ACTIVE OFF R
BV86 BYP Smk Prg DRV Stat 8784H: bit 6 ACTIVE OFF R
BV87 BYP Safety Status 8784H: bit 7 OPEN CLOSED R
BV88 BYP BAS Interlk Stat 8785H: bit 0 OPEN CLOSED R
BV89 BYP RUN Status 8785H: bit 1 RUN OFF R
BV90 BYP Fault Status 8785H: bit 2 FAULT OFF R
BV91 BYP Auto Xfer Status 8785H: bit 3 ACTIVE OFF R
BV92 BYP Remote Xfer Stat 8785H: bit 4 ACTIVE OFF R
BV93 BYP Energy Save Stat 8785H: bit 5 ACTIVE OFF R
BV94 BYP Motor 1 Sel Stat 8785H: bit 6 SELECT OFF R
BV95 BYP Motor 2 Sel Stat 8785H: bit 7 SELECT OFF R
BV96 BYP Drive Flt Status 8786H: bit 0 FAULT OFF R
BV97 BYP Safety Flt Stat 8786H: bit 1 FAULT OFF R
BV98 BYP BAS ILock Status 8786H: bit 2 FAULT OFF R
BV99 BYP Ext Fault Stat 8786H: bit 3 FAULT OFF R
BV100 Not Used BV100 8786H: bit 4 FAULT OFF R
BV101 BYP Motor OL Stat 8786H: bit 5 FAULT OFF R
BV102 BYP Motor 1 OL Stat 8786H: bit 6 FAULT OFF R
BV103 BYP Mtr 2 OL Stat 8786H: bit 7 FAULT OFF R
BV104 BYP Input Phase Loss 8787H: bit 0 FAULT OFF R
BV105 BYP Drive Comms 8787H: bit 2 FAULT OFF R
BV106 BYP Loss Of Load 8787H: bit 5 FAULT OFF R
BV107 BYP Option Brd Comms 8787H: bit 3 FAULT OFF R
<1> Refer to Accessing Bypass Parameters and the Enter Command on page 301 for an explanation of how to read and write drive parameters not
listed in the analog or binary objects.
u Device Object
The Device Object fully describes the BACnet device to the network. Notable is that the Device Object Instance ID and the
Device Object Name are configurable.
The Device Object Instance ID is a unique internetwork-wide numerical value. It is a 22-bit value that can range from 0 to
4,194,303. It is configurable by parameters Z3-08 and Z3-09. Any changes to these parameters will not take effect until the
power is cycled to the bypass.
The Device Object Name is a unique internetwork-wide character string. It is a 20-character string. It is writable from the
BACnet network. Any new string written will not take effect until the power is cycled to the bypass.
C.6 BACnet Objects Supported
300 YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual