Yaskawa AC Drive P1000 Bypass Technical Manual - Manual (Page 246)

B.8 H Parameters: Multi-Function Terminals
H parameters assign functions to the multi-function input and output terminals.
u H1: Multi-Function Digital Inputs
No.
(Addr.
Hex)
Name Description Values Page
H1-03
(400)
Multi-Function Digital Input
Terminal S3 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 3.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: 24
Min.: 3
Max.: 60
115
H1-04
(401)
Multi-Function Digital Input
Terminal S4 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 4.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: 14
Min.: 3
Max.: 60
115
H1-05
(402)
Multi-Function Digital Input
Terminal S5 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 5.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: 3
Min.: 3
Max.: 60
115
H1-06
(403)
Multi-Function Digital Input
Terminal S6 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 6.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: 4
Min.: 3
Max.: 60
115
H1-07
(404)
Multi-Function Digital Input
Terminal S7 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 7.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: 6
Min.: 3
Max.: 60
115
H1-08
(405)
Multi-Function Digital Input
Terminal S8 Function
Selection
Assigns a function to the multi-function digital inputs through Z2-oo = 8.
Refer to Table B.3 for descriptions of setting values.
Note: Set unused terminals to F.
Default: F
Min.: 3
Max.: 60
115
Table B.3 H1 Multi-Function Digital Input Selections
H1-oo
Setting
Function Description Page
3 Multi-Step Speed Reference 1
When input terminals are set to Multi-Step Speed References 1 through 3, switching
combinations of those terminals will create a multi-step speed sequence using the frequency
references set in d1-01 through d1-08.
115
4 Multi-Step Speed Reference 2
When input terminals are set to Multi-Step Speed References 1 through 3, switching
combinations of those terminals will create a multi-step speed sequence using the frequency
references set in d1-01 through d1-08.
115
6 Jog reference selection
Closed: Jog frequency reference (d1-17) selected. Jog has priority over all other reference
sources.
115
C Analog terminal input selection
Open: Function assigned by H3-14 is disabled.
Closed: Function assigned by H3-14 is enabled.
115
F Through mode
Select this setting when using the terminal in a pass-through mode. The terminal does not
trigger a drive function but can be used as digital input for the controller the drive is connected
to.
115
10 Up command
The drive accelerates when the Up command terminal closes, and decelerates when the Down
command closes. When both terminals are closed or both are open, the drive holds the
frequency reference. The Up and Down commands must always be used in conjunction with
one another.
115
11 Down command
The drive accelerates when the Up command terminal closes, and decelerates when the Down
command closes. When both terminals are closed or both are open, the drive holds the
frequency reference. The Up and Down commands must always be used in conjunction with
one another.
115
13 Reverse Jog Closed: Runs reverse at the Jog frequency d1-17 116
14 Fault Reset Closed: Resets faults if the cause is cleared and the Run command is removed. 117
19 PID disable
Open: PID control enabled
Closed: PID control disabled
117
24 External fault Normally Open, Always Detected, Coast to Stop 117
60 DC Injection Braking command Closed: Triggers DC Injection Braking. 117
B.8 H Parameters: Multi-Function Terminals
246 YASKAWA SIEP YAIP1B 01A YASKAWA AC Drive – P1000 Bypass Technical Manual