Yaskawa CIMR-LU Drives User Manual
Page 225
C Standards Compliance
YASKAWA ELECTRIC TOEP C710616 38F YASKAWA AC Drive L1000A Quick Start Guide
225
St
an
dar
d
s
Co
mplia
nce
C
Note: Use crimp insulated terminals or insulated tubing for wiring these connections. Wires should have a continuous maximum
allowable temperature of 75
°C (167°F) 600 V UL approved vinyl sheathed insulation. Ambient temperature should not exceed
40
°C (104°F).
2A0115
R/L1, S/L2, T/L3
2/0
1 to 2/0
M10
18 to 23
(159 to 204)
U/T1, V/T2, W/T3
2/0
1 to 2/0
–, +1
–
1/0 to 3/0
B1, B2
–
4 to 2/0
4
4
M8
9 to 11
(79.7 to 97.4)
2A0145
R/L1, S/L2, T/L3
4/0
2/0 to 4/0
M10
18 to 23
(159 to 204)
U/T1, V/T2, W/T3
4/0
3/0 to 4/0
–, +1
–
1 to 4/0
+3
–
1/0 to 4/0
4
4 to 2
9 to 11
(79.7 to 97.4)
2A0180
R/L1, S/L2, T/L3
1/0
× 2P
1/0 to 2/0
M10
18 to 23
(159 to 204)
U/T1, V/T2, W/T3
1/0
× 2P
1/0 to 2/0
–, +1
–
1 to 4/0
+3
–
1/0 to 4/0
4
4 to 1/0
9 to 11
(79.7 to 97.4)
2A0215
R/L1, S/L2, T/L3
3/0
× 2P
3/0 to 300
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3
3/0
× 2P
3/0 to 300
–, +1
–
3/0 to 300
+3
–
2 to 300
M10
18 to 23
(159 to 204)
3
3 to 300
M12
32 to 40
(283 to 354)
2A0283
R/L1, S/L2, T/L3
4/0
× 2P
3/0 to 300
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3
3/0
× 2P
3/0 to 300
–, +1
–
3/0 to 300
+3
–
3/0 to 300
M10
18 to 23
(159 to 204)
2
2 to 300
M12
32 to 40
(283 to 354)
2A0346
R/L1, S/L2, T/L3
250
× 2P
4/0 to 600
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3
4/0
× 2P
4/0 to 600
–, +1
–
250 to 600
+3
–
3/0 to 600
M10
18 to 23
(159 to 204)
1
1 to 350
M12
32 to 40
(283 to 354)
2A0415
R/L1, S/L2, T/L3
350
× 2P
250 to 600
M12
32 to 40
(283 to 354)
U/T1, V/T2, W/T3
300
× 2P
300 to 600
–, +1
–
300 to 600
+3
–
3/0 to 600
M10
18 to 23
(159 to 204)
1
1 to 350
M12
32 to 40
(283 to 354)
<1> When an EMC filter is installed, additional measures must be taken in order to comply with IEC/EN 61800-5-1. Refer to
<2> Drive models CIMR-LU2A0085 to 2A0415 require the use of closed-loop crimp terminals for UL/cUL compliance. Use only the tools
recommended by the terminal manufacturer for crimping.
Model
CIMR-LU
Terminal
Recommended
Gauge
AWG, kcmil
Applicable Gauge
AWG, kcmil
Screw
Size
Tightening Torque
N m (lb.in.)
TOEP_C710616_38F_5_0.book 225 ページ ２０１３年１２月４日 水曜日 午前９時５６分