Rockwell Automation 20D PowerFlex 700H and 700S Frame 9...14 Drives User Manual

Page 164

164

Rockwell Automation Publication PFLEX-IN006E-EN-P - July 2013

Appendix A

Specifications

Category

Specification

PowerFlex 700H

PowerFlex 700S

Protection

Drive

380/400V

480V

500V

600V

690V

380/400V

480V

500V

600V

690V

AC Input Overvoltage Trip:

611V AC

806V AC

675V AC

889V AC

AC Input Undervoltage Trip:

235VAC

326VAC

Adjustable

Bus Overvoltage Trip:

911VDC

1200V DC

911VDC

1200V DC

Bus Undervoltage Shutoff/Fault:

333VDC

461VDC

Adjustable

Nominal Bus Voltage (Full Load):

517VDC

621VDC

645VDC

776VDC

890VDC

540VDC

648VDC

645VDC

810VDC

931V DC

Heat Sink Thermistor:

Monitored by microprocessor overtemp trip

Drive Overcurrent Trip
Software Overcurrent Trip:
Hardware Overcurrent Trip:
Instantaneous Current Limit:

—
360% of rated Heavy Duty current (typical)
—

Calculated value, 105% of motor rated to 200% of drive rated
360% of rated Heavy Duty current (typical)
—

Line transients:

up to 6000 volts peak per IEEE C62.41-1991

Up to 6000 volts peak per IEEE C62.41-1991

Control Logic Noise Immunity:

Showering arc transients up to 1500V peak

Power Ride-Thru:

15 milliseconds at full load

Logic Control Ride-Thru:

0.5 seconds minimum, 2 seconds typical

0.25 seconds, drive not running

Ground Fault Trip:

Phase-to-ground on drive output

Short Circuit Trip:

Phase-to-phase on drive output

Environment

Altitude:

1000 m (3300 ft.) maximum without derating. Derate the drive by 1% for every
100 m (328 ft.) above 1000 m (3300 ft.).

Maximum Surrounding Air Temperature without
De-rating:

Based on drive rating, refer to Drive Ratings on page

167

Based on drive rating, refer to Drive Ratings on page

167

Storage Temperature (all const.):

–40 to 60° C (–40 to 140° F)

–40 to 70° C (–40 to 158° F)

Atmosphere:

Important: Drive must not be installed in an area where the ambient
atmosphere contains volatile or corrosive gas, vapors or dust. If the drive is not
going to be installed for a period of time, it must be stored in an area where it
will not be exposed to a corrosive atmosphere.

Relative Humidity:

5 to 95% non-condensing

Shock:
Non-operational

15G peak for 11ms duration (

1.0 ms)

15G peak for 11ms duration (

1.0 ms)

Vibration:

2 mm (0.0787 in.) displacement, 1G peak
EN50178 / EN60068-2-6

Sound:

Frame

Sound Level

Back- ground
Noise Level

Note: Sound pressure level is
measured at 1 meter. All
devices measured are 400V
IP21 and in power up mode.

Frame

Sound Level

Back- ground
Noise Level

Note: Sound pressure level is
measured at 1 meter. All
devices measured are 400V
IP21 and in power up mode.

78 dba

49 dba

78 dba

49 dba

77 dba

49 dba

77 dba

49 dba

76d ba

46 dba

76d ba

46 dba

Electrical

AC Input Voltage Tolerance:

10%

Frequency Tolerance:

47…63 Hz.

Input Phases:

Three-phase input provides full rating for all drives. Single-phase operation
provides 50% of rated current.

Displacement Power Factor:

0.98 across entire speed range.

Efficiency:

97.5% at rated amps, nominal line volts.

Maximum Short Circuit Rating:

≤

200,000 Amps symmetrical.

≤

200,000 Amps symmetrical.

Actual Short Circuit Rating:

Determined by AIC rating of installed fuse/circuit breaker.

Maximum Drive to Motor Power Ratio:

Recommended not greater than 2:1 ratio.

Drive to motor rating cannot exceed a 2:1 ratio.

This manual is related to the following products:

20C PowerFlex 700H and 700S Frame 9...14 Drives