Rockwell Automation 20D PowerFlex 700H and 700S Frame 9...14 Drives User Manual

Rockwell Automation Equipment

PowerFlex 700H Adjustable Frequency AC Drive and PowerFlex 700S High
Performance AC Drive

Frames 9...14

Installation Instructions

This manual is related to the following products:

20C PowerFlex 700H and 700S Frame 9...14 Drives

Table of contents

Document Outline

PowerFlex 700H and 700S AC Drives, Frames 9...14, Installation Instructions
Summary of Changes
- New and Updated Information
Table of Contents
Preface
- Drive Description
- Enclosure Options
- Drive Frame Sizes
- Conventions
- General Precautions
- General Precautions, Continued
- Additional Resources
Chapter 1 - General Installation Information
- AC Supply Source Considerations
- General Grounding Requirements
- Fuses and Circuit Breakers
- Power Wiring
- EMC Instructions
- Using Input/Output Contactors
  - Input Contactor Precautions
  - Output Contactor Precaution
- Common Bus/Precharge
  - DC Input Precharge Control Wiring
Chapter 2 - Control Wiring for PowerFlex 700H Drives
- 700H Control Circuit Board Designations
- I/O Terminal Blocks
- I/O Cable Grounding
- Analog I/O Configuration
- Hardware Enable Circuitry
- Auxiliary Power Supply
- I/O Wiring Examples
- Reference Control Sources
- Auto/Manual Examples
Chapter 3 - Control Wiring for PowerFlex 700S Drives with Phase II Control
- I/O Wiring
- Main Control Board Switch and Jumper Settings
- I/O Terminal Blocks
  - Wiring the Main Control Board I/O Terminals
- I/O Wiring Examples
- Hardware Enable Circuitry
- Auxiliary Power Supply
- Removing the Control Cassette
Chapter 4 - Communication Options
- Communication Module Locations
- Communication Configurations
  - Typical Programmable Controller Configurations
  - Logic Command/Status Words
Chapter 5 - Frame 9 Mechanical Installation
- Ungrounded, Unbalanced or High Resistive Ground Installations
- Minimum Mounting Clearances
- Operating Temperatures
- Nameplate Location
- Dimensions
- Lifting Frame 9 Drives
- Remove the Drive Covers
- Power Wiring
  - Frame 9 DC Bus/Brake Connections
- Routing for I/O Wiring and Communication Cabling
Chapter 6 - Frame 10 Mechanical Installation
- Minimum Mounting Clearances
- Operating Temperatures
- Dimensions
- Lifting and Mounting Frame 10 Drives
- Remove the Protective Covers
- Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations
- Power Wiring
Chapter 7 - Frame 11 Mechanical Installation
- Minimum Mounting Clearances
- Operating Temperatures
- Dimensions
- Lifting and Mounting Frame 11 Drives
- Remove the Protective Covers
- Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations
- Power Wiring
  - AC Input Wiring
Chapter 8 - Frame 12 Mechanical Installation
- Minimum Mounting Clearances
- Operating Temperatures
- Dimensions
- Lifting and Mounting Frame 12 Drives
- Remove the Protective Covers
- Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations
- Power Wiring
  - Input Power Wiring
  - Output Power Wiring
Chapter 9 - Frame 13 Mechanical Installation
- Minimum Mounting Clearances
- Operating Temperatures
- Dimensions
- Lifting and Mounting Frame 13 Drives
- Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations
- Remove the Protective Covers from the Converter Unit
- Remove the Protective Covers from the Inverter Unit
  - Remove the Lower Protective Screen
  - Remove the Protective Covers
- Power Wiring
Chapter 10 - Frame 14 Mechanical Installation
- Minimum Mounting Clearances
- Operating Temperatures
- Dimensions
- Lifting and Mounting Frame 14 Drives
- Ungrounded, High Resistive Ground or Grounded B Phase Delta Installations
- Remove the Protective Covers from the Converter Unit(s)
- Power Wiring
- Remove the Protective Covers from the Inverter Units
- Frame 14 Circuit Breakers
Appendix A - Specifications
- Drive Catalog Number Designations
  - Drive Ratings
- Drive Fuse & Circuit Breaker Ratings
  - Fusing
  - Circuit Breakers
Appendix B - PowerFlex 700S Stegmann Hi-Resolution Encoder Feedback Option
- Option Card Specifications
- Supported Encoders
- Wiring the Hi-Resolution Feedback Option Card to an Encoder
  - Recommended Cables and Wiring Diagrams for the Stegmann Hi- Resolution Feedback Option Card
Appendix C - PowerFlex 700S Resolver Feedback Option Card
- Option Card Specifications
- Compatible Resolvers
- Wiring the Resolver Feedback Option Card to a Resolver
  - Recommended Cable
Appendix D - PowerFlex 700S Multi-Device Interface (MDI) Option Card
- MDI Option Card Specifications
- Supported Linear Sensors
- Supported Rotary Encoders
- Wiring the MDI Option Card
  - Recommended Cables and Wiring Diagrams for the MDI Option Card
Appendix E - Instructions for ATEX Approved PowerFlex 700H Drives in Group II Category (2) Applications with ATEX Approved Motors
- General Information
- Motor Requirements
- Drive Wiring
- Configuration
- Removing the 20C-DG1 Option Board
- Verify Operation
Appendix F - History of Changes
- PFLEX-IN006D-EN-P, March 2006
- PFLEX-IN006C-EN-P, October 2004
Index
Back Cover