Rockwell Automation FlexPak 3000 Power Module SW-Version 4.3 - Manual (Page 4)

TABLE OF CONTENTS
FlexPak 3000 49’1340 e II
4.0 Drive Setup and Adjustment 4-1...4-16
4.1 General ....................................................................................................................... 4-1
4.2 Test Equipment Needed ............................................................................................. 4-1
4.3 Power Off Inspection................................................................................................... 4-1
4.4 Motor Ground Check................................................................................................... 4-1
4.5 Jumper Settings .......................................................................................................... 4-2
4.5.1 Set Regulator Type - J15 Jumper ................................................................... 4-3
4.5.2 Set Program Disable/Enable (OIM PROGRAM) - J16 Jumper ....................... 4-4
4.5.3 Set Field Loss Enable/Disable (FIELD LOSS DETECT) - J20 ........................ 4-4
4.5.4 Set Tacho Loss / Open Arm. Enable/Disable (TACHO LOSS DET) - J26 ..... 4-4
4.5.5 Field Supply Jumper Connection (FIELD SUPPLY) - J21............................... 4-5
4.5.6 Manual Reference (MANUAL REF) - J19 Jumper .......................................... 4-5
4.5.7 Tachometer Voltage Range/Scale (TACH V RANGE/SCALE) - J14 / J11...... 4-5
4.5.8 Analog Auto Reference (AUTO REF) - J12 and J10 Jumpers ........................ 4-6
4.5.9 Armature Current Feedback Scaling (ARM I FB RB) - J18 Jumper ................ 4-6
4.5.10 Check position of the FILTER SELECT - J28 Jumper ................................... 4-6
4.5.11 Check position of the POWER INTERFACE- J30 Jumper .............................. 4-6
4.6 Powering Up the Drive ................................................................................................ 4-7
4.7 OIM Screen Contrast Adjustment ............................................................................... 4-7
4.8 About the Main Menu.................................................................................................. 4-8
4.9 How to Access the Menus/Parameters....................................................................... 4-8
4.10 Verify the Correct Direction of Motor Rotation .......................................................... 4-10
4.11 Determination of DC Tachometer Lead Polarity ....................................................... 4-10
4.12 Adjustments .............................................................................................................. 4-10
4.12.1 Perform Armature Voltage Zero Adjust ....................................................... 4-11
4.12.2 Perform Analog Tachometer Zero Adjust.................................................... 4-11
4.13 Language Selection .................................................................................................. 4-11
4.14 Programming Features ............................................................................................. 4-12
4.14.1 Password (PASSWORD) .............................................................................. 4-12
4.14.2 How to Enable/Disable Program Protection .................................................. 4-13
4.14.3 Memory Operations....................................................................................... 4-13
4.14.4 Reset Clock ................................................................................................... 4-14
4.14.5 Define User Units .......................................................................................... 4-14
4.14.5.1 Define Speed Units ....................................................................... 4-14
4.14.5.2 Define Load Units.......................................................................... 4-16
5.0 How to Change Parameter Values 5-1..5-4
5.1 Introduction ................................................................................................................. 5-1
5.2 Integer Value Entry Screen......................................................................................... 5-1
5.3 Standard Choice Integer Value Entry Screen ............................................................. 5-2
5.4 Selector Switch or Boolean Value Entry Screen......................................................... 5-4
6.0 Quick Start 6-1..6-10
6.1 Introduction ................................................................................................................. 6-1
6.2 About the Quick Start Exit Menu ................................................................................. 6-1
6.3 How to Step through Quick Start................................................................................. 6-1
6.4 Self
Tuning .................................................................................................................. 6-7
6.4.1 Self Tune Setup ............................................................................................ 6-7
6.4.2 Execute Self Tuning ...................................................................................... 6-8
6.5 Final Adjustments...................................................................................................... 6-10
6.5.1 Nominal A-C Line Adjustments ...................................................................... 6-10
6.5.1.1 Perform Nominal AC-Line Frequency Adjust ................................... 6-10
6.5.1.2 Perform Nominal AC-Line Volts Adjust ............................................ 6-10