Lenze EVF9333−xV User Manual
Ä.cn:ä, 9300 vector
This manual is related to the following products:
Table of contents
Document Outline
- Frequency inverter 9300 vector
- Contents
- 1 Preface
- 2 Safety instructions
- 3 Technical data
- 4 Installation of the standard device
- 5 Wiring of the standard device
- 5.1 Important notes
- 5.2 Notes on project planning
- 5.2.1 Supply forms / electrical supply conditions
- 5.2.2 Operation on public supply systems (compliance with EN 61000-3-2)
- 5.2.3 Controllers in the IT system
- 5.2.4 Operation at earth-leakage circuit breaker (e.l.c.b.)
- 5.2.5 Interaction with compensation equipment
- 5.2.6 Discharge current for mobile systems
- 5.2.7 Optimisation of the controller and mains load
- 5.2.8 Reduction of noise emissions
- 5.2.9 Mains choke/mains filter assignment
- 5.2.10 Motor cable
- 5.3 Basics for wiring according to EMC
- 5.4 Standard devices in the power range 0.37 ... 11 kW
- 5.5 Standard devices in the power range 15 ... 30 kW
- 5.6 Standard devices in the power range of 55 kW
- 5.7 Standard devices in the power range 75 ... 90 kW
- 5.8 Control terminals
- 5.9 Wiring of the system bus (CAN)
- 5.10 Wiring of the feedback system
- 5.11 Wiring of digital frequency input / digital frequency output
- 5.12 Communication modules
- 6 Commissioning
- 6.1 Before switching on
- 6.2 Selection of the correct operating mode
- 6.3 Parameter setting with the XT EMZ9371BC keypad
- 6.4 Controller inhibit
- 6.5 Changing the assignment of the control terminals X5 and X6
- 6.6 Adjusting the motor
- 6.7 Setting the speed feedback
- 6.8 Operating mode
- 6.9 Switching frequency of the inverter
- 6.10 Acceleration, deceleration, braking, stopping
- 6.11 Optimising the operating behaviour
- 7 Parameter setting
- 7.1 Important notes
- 7.2 Parameter setting with the XT EMZ9371BC keypad
- 7.2.1 General data and operating conditions
- 7.2.2 Installation and commissioning
- 7.2.3 Display elements and function keys
- 7.2.4 Changing and saving parameters
- 7.2.5 Loading a parameter set
- 7.2.6 Transferring parameters to other standard devices
- 7.2.7 Activating password protection
- 7.2.8 Diagnostics
- 7.2.9 Menu structure
- 8 Configuration
- 8.1 Important notes
- 8.2 Function blocks
- 8.2.1 Diameter calculator (DCALC)
- 8.2.2 Master frequency input (DFIN)
- 8.2.3 Master frequency output (DFOUT)
- 8.2.4 Master frequency ramp-function generator (DFRFG)
- 8.2.5 Master frequency processing (DFSET)
- 8.2.6 Internal motor control with V/f characteristic control (MCTRL1)
- 8.2.7 Internal motor control with vector control (MCTRL2)
- 8.3 Monitoring
- 8.3.1 Fault responses
- 8.3.2 Monitoring times for process data input objects
- 8.3.3 Maximum speed
- 8.3.4 Motor
- 8.3.5 Controller current load (I x t monitoring)
- 8.3.6 Motor temperature
- 8.3.7 Current load of motor (I2 x t monitoring: OC6, OC8)
- 8.3.8 Heatsink temperature
- 8.3.9 DC-bus voltage
- 8.3.10 External error (EEr)
- 8.4 Overview of monitoring functions
- 8.5 Code table
- 8.6 Selection lists
- 8.7 Table of attributes
- 9 Troubleshooting and fault elimination
- 10 DC-bus operation
- 11 Safety engineering
- 12 Accessories (overview)
- 13 Appendix