Lenze EVF9333−xV - Manual (Page 501)

Appendix
Index
13
13.2
l
13.2−3 EDSVF9333V EN 6.2−04/2012
Display of operating data, 9.1−1
Display values, 9.1−1
− Calibration, 9.1−1
Disposal, 2.1−3
Distributed supply, 10.4−1
Drive behaviour
− Controller inhibit, 6.4−1
− in the event of faults, 9.3−1
− Influence of the motor cable length, 5.2−10
Drive errors, 9.4−1
E
E.l.c.b., 5.2−3
− operation at, 5.2−3
Earth−leakage circuit breaker, 5.2−3
− operation at, 5.2−3
Electrical installation, system bus (CAN), 5.9−1
EMC, what to do in case of interferences, 5.3−6
Emergency−off, Controller inhibit, 6.4−1
EMZ9371BC keypad, changing parameters, 7.2−7 , 7.2−8
EN 61000−3−2, 3.1−2 , 5.2−1
− operation on public supply systems, 5.2−1
Entry of motor data, 6.6−1
Error analysis, Via history buffer, 9.2−1
Error messages, 9.5−1
− causes and remedies, 9.5−1
− configuration, 8.41
− General, 9.5−1
− Resetting, 9.5−5
Exceeding of the maximum speed (NMAX), 8.3−3
Explanations, Code table, 8.5−1
External error (EEr), 8.3−8
F
Failure of a motor phase, 8.3−4
Fault analysis, Via history buffer, 9.2−1
Fault elimination, 9.4−1
Fault messages
− causes and remedies, 9.5−1
− OC3 in clamp operation, 9.4−2
Fault responses, 8.3−1
Feedback system, wiring, 5.10−1
Field controller, 6.8−8 , 8.5−8
Field frequency
− maximum, 6.10−1
− Minimum, 6.10−1
Flying restart circuit, 2.3−1
Free spaces, 3.1−2
Function blocks, 8.2−1
− diameter calculator (DCALC1), 8.2−1
− internal motor control, vector control (MCTRL2), 8.2−48
− master frequency input (DFIN), 8.2−5
− master frequency output (DFOUT), 8.2−8
− master frequency processing (DFSET), 8.2−18
− master frequency ramp−function generator (DFRFG1),
8.2−13
Function keys, keypad XT EMZ9371BC, 7.2−4
Functional test, safety function, 11.4−2 , 11.4−5
Fuses, 10.3−1
− mains connection, 5.4−5 , 5.5−5 , 5.6−5 , 5.7−5
G
General accessories, 12.1−1
General data, 3.1−1 , 7.2−1
H
Harmonic currents
− Limitation according to EN 61000−3−2, 5.2−1
− limitation in accordance with EN 61000−3−2, 3.1−2
Heatsink temperature, monitoring, 8.3−7
History buffer, 9.2−1
− Assembly, 9.2−2
− delete, 9.2−2
I
Imax limit in motor mode, 6.6−13 , 8.2−27 , 8.2−50 , 8.5−4
− in generator mode, 6.6−13 , 8.2−27 , 8.2−50 , 8.5−4
Incremental encoder
− At X8, 5.10−2 , 6.7−2
− at X9, 5.10−3 , 6.7−3
− operation with, 8.2−59
− with HTL level, 5.10−3 , 6.7−3
− With TTL level, 5.10−2 , 6.7−2
Input signals
− Analog, Configuration, 6.5−4
− Digital, Configuration, 6.5−1