Lenze EVF9333−xV - Manual (Page 408)

Configuration
Code table
8
8.5
l
8.5−60 EDSVF9333V EN 4.0−11/2007
IMPORTANT Possible settings Code
Selection Lenze Name No.
C0912 OV delay time à − {1 ms} − Delay time of the pulse enable
after an OU message
à Depending on C0082, C0086,
C0087, C0088, C0089, C0090,
C0091, C0092
A change of one of the codes
resets C0912 to the time of the
selected motor
l The time is derived from the
double rotor time constant
^
8.2−25
^
8.2−48
^ 9.4−3
C0913
s
OV handling 0 Value of the motor current during
the flying restart process or after
an OU message
l When C0913 = 1, the motor is
driven with reduced current to
the setpoint speed during the
flying restart process of after
an OU message.
l The setting is only effective for
the drives EVF9326 ... EVF9333
^
8.2−25
^
8.2−48
0 inactive Non−reduced motor current
1 active Reduced motor current
C0940 Numerator 1 −32767 {1} 32767 Configuration of conversion factor
with numerator and denominator,
function block CONV1
See System
Manual
(extension)
C0941 Denominator 1 1 {1} 32767
OUT [%] + IN [%] @ C0940
C0941
C0942
s
CFG: IN 1000 FIXED0% ^ Selection list 1 Configuration of analog input
signal, function block CONV1
C0943 DIS: IN −199.99 {0.01 %} 199.99 Function block CONV1
l Display of the signal linked in
C0942
C0945 Numerator 1 −32767 {1} 32767 Configuration of conversion factor
with numerator and denominator,
function block CONV2
See System
Manual
(extension)
C0946 Denominator 1 1 {1} 32767
OUT [%] + IN [%] @ C0945
C0946
C0947
s
CFG: IN 1000 FIXED0% ^ Selection list 1 Configuration of analog input
signal, function block CONV2
C0948 DIS: IN −199.99 {0.01 %} 199.99 Function block CONV2
l Display of the signal linked in
C0947
C0950 Numerator 1 −32767 {1} 32767 Configuration of conversion factor
with numerator and denominator,
function block CONV3
See System
Manual
(extension)
C0951 Denominator 1 1 {1} 32767
OUT [%] + IN [rpm] @ 100 %
15000 rpm
@ C0950
C0951
C0952
s
CFG: IN 1000 FIXED0% ^ Selection list 1 Configuration of analog input
signal, function block CONV3
C0953 DIS: IN −199.99 {0.01 %} 199.99 Function block CONV3
l Display of the signal linked in
C0952
C0955 Numerator 1 −32767 {1} 32767 Configuration of conversion factor
with numerator and denominator,
function block CONV4
See System
Manual
(extension)
C0956 Denominator 1 1 {1} 32767
OUT [%] + IN [rpm] @ 100 %
15000 rpm
@ C0955
C0956
C0957
s
CFG: IN 1000 FIXED0% ^ Selection list 1 Configuration of analog input
signal, function block CONV4
C0958 DIS: IN −199.99 {0.01 %} 199.99 Function block CONV4
l Display of the signal linked in
C0957