Lenze EVF9333−xV - Manual (Page 289)

Configuration
Function blocks
Internal motor control with V/f characteristic control (MCTRL1)
8
8.2
8.2.6
l
8.2−27 EDSVF9333V EN 6.2−04/2012
IMPORTANT Possible settings Code
Selection Lenze Name No.
C0018 fchop
6 Switching frequency of the
inverter
l General rule: the lower the
switching frequency the
– lower the power loss
– higher the noise generation
– better the concentricity
factor
– Observe derating
information at high
switching frequencies
l The max. output frequency
(f
out
) amounts to:
– f
chop
= 16 kHz
Þf
out
= 600 Hz
– f
chop
= 8 kHz Þf
out
= 300 Hz
– f
chop
= 4 kHz Þf
out
= 150 Hz
– f
chop
= 2 kHz Þf
out
= 150 Hz
^ 6.9−1
0 auto chop automatic
change−over of the
switching
frequency
between
16/8/2 kHz
1 2 kHz sin optimised smooth
running
2 4 kHz f_top power−optimised
3 8 kHz f_top power−optimised
4 8 kHz sin noise optimised
5 16 kHz sin noise optimised
6 auto 8/2 kHz noise /
power−optimised
with automatic
change−over to
low switching
frequency
C0021 slipcomp à −20.00 {0.01 %} 20.00 Slip compensation
à Change of C0086, C0087 or
C0089 sets C0021 to the
calculated rated slip of the
motor
l When changing over to the
vector control mode, C0021 is
set to 0
^
6.11−1
^
8.2−25
^
8.2−48
C0022 IMAX CURRENT à 0 {0.01 A} − I
max
limit in motor mode
à Depending on C0086
^
6.6−13
C0023 Imax gen. à 0 {0.01 A} − I
max
limit in generator mode
à Depending on C0086
^
6.6−13
C0036 DC brk value 0.0 0.0 {0.1 A} − Set DC braking current
à depends on the controller
^
8.2−25
^
8.2−48
C0042 DIS: QSP Quick stop
l Display only
^
8.2−25
^
8.2−48
0 QSP inactive Quick stop is not active
1 QSP active Quick stop is active
C0050 MCTRL−NSET2 −100.00 {0.01 %} 100.00 Speed setpoint, function block
MCTRL
l Display of the speed in [%] of
C0011
^
8.2−25
^
8.2−48
C0051 MCTRL−NACT −36000 {1 rpm} 36000 Actual speed value, function block
MCTRL
l Read only
^
8.2−25
^
8.2−48
C0052 MCTRL−Umot 0 {1 V} 800 Motor voltage, function block
MCTRL
l Read only
l MCTRL−VACT = 100 % = C0090
^
8.2−25
^
8.2−48
C0053 UG−VOLTAGE 0 {1 V} 900 DC−bus voltage, function block
MCTRL
l Read only
l MCTRL−DCVOLT = 100 % =
1000 V
^
8.2−25
^
8.2−48
C0054 IMot 0.0 {0.1 A} 500.0 Current motor current, function
block MCTRL
l Read only
l MCTRL−IACT = 100 % = C0022
^
8.2−25
^
8.2−48