List of figures – Teledyne GFC-7000T - Trace CO2 Analyzer - manual User Manual
Page 15

Table of Contents
Model GFC7000TA Carbon Dioxide Analyzer
Teledyne Analytical Instruments
xv
LIST OF FIGURES
Figure 3-1:
Front Panel Layout ...................................................................................................................... 11
Figure 3-2:
Display Screen and Touch Control ............................................................................................. 12
Figure 3-3:
Display/Touch Control Screen Mapped to Menu Charts ............................................................. 14
Figure 3-4:
Rear Panel Layout ....................................................................................................................... 15
Figure 3-5:
Internal Chassis Layout ............................................................................................................... 17
Figure 3-6:
Optical Bench Layout .................................................................................................................. 18
Figure 3-7:
GFC 7000TA Internal Gas Flow .................................................................................................. 19
Figure 3-8:
Analog In Connector .................................................................................................................... 20
Figure 3-9:
Pneumatic Connections–Basic Configuration–Using Bottled Span Gas .................................... 27
Figure 3-10:
Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ............................ 27
Figure 3-11:
Pneumatic Connections with Ambient Zero/Ambient Span Valves (OPT 50A) .......................... 30
Figure 3-12:
Pneumatic Connections with Ambient Zero/Ambient Span Valves (Opt 50A) and
External Zero Air Scrubber .......................................................................................................... 30
Figure 3-13:
Pneumatic Connections with Ambient Zero/Pressurized Span Valves (OPT 50B) .................... 31
Figure 3-14:
Pneumatic Connections with Ambient Zero/Pressurized Span Valves (Opt 50B) and
External Zero Air Scrubber .......................................................................................................... 31
Figure 3-15:
Example of Pneumatic Set up for Multipoint Calibration ............................................................. 32
Figure 3-16:
O2 Sensor Calibration Set Up ..................................................................................................... 40
Figure 5-1:
Current Loop Option Installed on the Motherboard ..................................................................... 52
Figure 5-2:
Internal Pneumatic Flow – Ambient Zero/Pressurized Span Valves ........................................... 55
Figure 5-3:
Internal Pneumatic Flow – Ambient Zero/Ambient Span ............................................................ 56
Figure 5-4:
Multi-drop/LVDS PCA Seated on CPU ....................................................................................... 58
Figure 5-5:
Oxygen Sensor - Principle of Operation ...................................................................................... 59
Figure 5-6:
GFC 7000TA – Internal Pneumatics with O2 Sensor Option 65 ................................................. 60
Figure 6-1:
Front Panel Display ..................................................................................................................... 63
Figure 6-2:
Viewing TEST Functions ............................................................................................................. 66
Figure 6-3:
Viewing and Clearing GFC 7000TA WARNING Messages ........................................................ 68
Figure 6-4:
Default DAS Channels Setup ...................................................................................................... 75
Figure 6-5:
APICOM User Interface for DAS Configuration .......................................................................... 88
Figure 6-6:
Analog Output Connector Pin Out ............................................................................................... 89
Figure 6-7:
Rear Panel Connector Pin-Outs for COM1 & COM2 in RS-232 Mode ..................................... 103
Figure 6-8:
CPU Connector Pin-Outs for COM1 & COM2 in RS-232 Mode ............................................... 104
Figure 6-9:
Multidrop/LVDS PCA Seated on CPU ....................................................................................... 114
Figure 6-10:
RS232-Multidrop PCA Host/Analyzer Interconnect Diagram .................................................... 115
Figure 6-11:
Setup for Calibrating Analog Voltage Outputs .......................................................................... 130
Figure 6-12:
Setup for Calibrating Current Outputs ....................................................................................... 132
Figure 6-13:
Status Output Connector ........................................................................................................... 143
Figure 6-14:
Control Inputs ............................................................................................................................ 145
Figure 6-15:
APICOM Remote Control Program Interface ............................................................................ 152
Figure 7-1:
Pneumatic Connections–Basic Configuration–Using Bottled Span Gas .................................. 162
Figure 7-2:
Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator .......................... 163
Figure 7-3:
Pneumatic Connections – Ambient Zero/Pressurized Span Valves ........................................ 166
Figure 7-4:
Pneumatic Connections – Ambient Zero/Pressurized Span Valves and External Zero Air
Scrubber .................................................................................................................................... 167
Figure 7-5:
Pneumatic Connections – Ambient Zero/Ambient Span Valves ............................................... 167
Figure 7-6:
Pneumatic Connections – Ambient Zero/Ambient Span Valves with External Zero Air
Scrubber .................................................................................................................................... 168
Figure 8-1:
Sample Particulate Filter Assembly .......................................................................................... 184
Figure 9-1:
Measurement Fundamentals ..................................................................................................... 188
Figure 9-2:
GFC Wheel ................................................................................................................................ 188
Figure 9-3:
Measurement Fundamentals with GFC Wheel ......................................................................... 189
Figure 9-4:
Affect of CO2 in the Sample on CO2 MEAS & CO2 REF ......................................................... 190
Figure 9-5:
Effects of Interfering Gas on CO2 MEAS & CO2 REF .............................................................. 191