Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) User Manual
Page 57
– 57 –
Chapter 5 Basic Operations — Wipe
f
Set the size restriction on the amount of transition.
6
Set [Return Time] in the [Pattern Limit] column.
f
Set the transition time to the position of the fader lever when [Pattern Limit] is set to [Off] from [On].
7
Set [X‑Pos] and [Y‑Pos] in the [Position] column.
f
Set the start position of the next pattern waveforms.
- WIPE: 11, 12, 13, 14, 15
- SQ: 41, 42, 43, 44, 45, 51, 52, 53, 54
f
These can be set only when the target pattern is selected in the background.
Either operate the fader lever or press the
Example) When [X-Pos] is set to [
−
50], and [Y-Pos] is set to [
−
50]
The next screen (or key) appears from the bottom left, and wipes in towards the center of the screen.
8
Set [Size] in the [Position] column.
f
Set the start size of the next pattern waveforms.
- SQ: 51, 52, 53, 54
Setting trimming, aspect ratio
Set the behavior for the trimming and aspect ratio. This is applied to the background transition.
1
Select the
→
[BKGD]
→
[Position] tab.
2
Select an item in [Trim] in the [Trim] column.
f
Set the trimming for the pattern waveforms of SQ, SL, and 3D.
[Off]
Does not perform trimming.
[16:9]
Trims the edges around a source at a certain amount. This setting is used when a black border is seen around the
source.
The edges are trimmed at a certain amount when SD is selected as the system format.
[4:3]*
1
Performs trimming in the 4:3 aspect ratio and releases the trimming when the transition is completed.
[4:3 Smooth]*
1
Performs trimming in the 4:3 aspect ratio, and smoothly executes transition to the 16:9 video.
[Manual]*
2
Trims the waveform using the values set in [Trim Adjust1] and [Trim Adjust2].
*1 Disabled when SD is selected as the system format.
*2 Enabled when the following pattern waveforms are selected.
SQ: 41, 51 - 54
3
Select an item in [Manual] in the [Trim] column.
[Free]
Sets the amount of trimming for [Left], [Right], [Top], and [Bottom] separately.
[Pair]
Changes the settings in such a way that the [Left] and [Right] trimming amounts, and the [Top] and [Bottom] trimming
amounts are the same. (This makes for a top-bottom and left-right symmetry.)
4
Select an item in [4:3 Auto] in the [Trim] column.
f
Set the target sources for automatic trimming ([4:3] or [4:3 Smooth]). Enabled when HD is selected as the system format.
[Off]
All input sources are targeted for automatic trimming.
[On]
The input sources for which [Edge Crop] is selected in the up-converter setting are targeted for automatic trimming. Input
sources for which an item other than [Edge Crop] is selected are trimmed in [16:9].
5
Set [WipeAspect] in the [Trim] column.
f
Adjust the aspect ratio of the wipe pattern.
f
The following pattern waveforms are changed.
- WIPE: 11 - 15
- SQ: 42 - 45
f
SQ41 and 51 to 54 are not applicable. The aspect ratio is adjusted with [Trim], [Trim Adjust1], or [Trim Adjust2].
6
Select an item in [Smooth] in the [Trim] column.
[OFF]
The aspect ratio for set wipe pattern will be constant regardless of the transition.
For SQ waveform, it may become discontinuous at the edge of transition.
[ON]
The aspect ratio is changed from the aspect ratio of the preset wipe pattern to the standard ratio in accordance with the
transition.
f
Modifies the next pattern waveforms.
- WIPE: 11 - 15
- SQ: 42 - 45
f
SQ41 and 51 to 54 are also applicable. [Trim Adjust1] and [Trim Adjust2] will change to the standard ratio when [Trim] is set to [Manual].
Setting the 3D (turn page) effect
A lighting effect can be added to a wipe pattern. Alternatively, the parameters for turn page effect can be set.
f
These effects can be set for background transitions and key transitions.