beautypg.com

Background transition, Selecting a bus, Selecting a bus using the shift function – Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) User Manual

Page 53: Selecting the bus mode, Transition operations

background image

– 53 –

Chapter 5 Basic Operations — Background transition

Background transition

Selecting a bus

Select sources to be used for background transitions.

1

Press the crosspoint buttons.

f

Depending on the operating status, the buttons pressed will light in one of three color patterns.

Type

Color when lit*

Description

High tally

[Red]

Lights when the selected source is included in the on-air output.

Low tally

[Yellow]

Lights when the selected source is not included in the on-air output but

included in the program output.

Preset tally

[Green]

Lights when the selected source is included in neither the on-air output

nor the program output.

* Indicates the default colors. To change the colors, select the button on the top menu

[CTRL PANEL]

[Button Color] tab

[Select Button]

column.

f

The color when lit for the buttons not selected can also be set by source or by block. (page 152)

Selecting a bus using the SHIFT function

The SHIFT function is to switch pages of the crosspoint buttons with the <2nd PAGE>/<3rd PAGE> button.
There are two ways to perform the SHIFT function.

All SHIFT

Use the <2nd PAGE>/<3rd PAGE> button to switch all pages of buses included in the corresponding ME at once.

(page 24)

Single SHIFT

Assign the <2nd PAGE>/<3rd PAGE> button to the crosspoint buttons to switch pages. (page 131)

Using the assigned button, only the pages of individual bas can be switched.

The <2nd PAGE>/<3rd PAGE> buttons are available in two modes. The setting can be changed using the menu. (page 135)

[Normal]

The buttons are turned on only while they are pressed.

[Page Lock]

The buttons are turned on and off each time they are pressed.

Selecting the bus mode

Select the A/B bus system or the flip‑flop system (PGM/PST system).

1

Select the button

[OPERATE]

[Transition] tab.

2

Set an item in [Bus Mode Type] in the [Bus Mode] column.

[Common]

Set the same bus mode in ME1 and ME2.

Setting of the [Bus Mode] column

[Bus Mode] is applied to both ME1 and ME2.

[Each]

Different bus modes can be set for ME1 and ME2.

Settings of the [Each Bus Mode1] column

[Bus Mode ME1] and [Bus Mode ME2] are applied to ME1 and ME2

respectively.

3

Select an item in [Bus Mode] in the [Bus Mode] column, and [Bus Mode ME1]/[Bus Mode ME2] in the [Each Bus Mode1] column.

[A/B]

When the fader lever is at side A, the signals selected on the A bus are used as the source of the PGM bus.

When the fader lever is at side B, the signals selected on the B bus are used as the source of the PGM bus.

[PGM‑A/PST‑B]

Using a flip‑flop system, the signals selected on the A bus are always used as the source of the PGM bus, and the

signals selected on the B bus are always used as the source of the PST bus.

[PGM‑B/PST‑A]

Using a flip‑flop system, the signals selected on the B bus are always used as the source of the PGM bus, and the

signals selected on the A bus are always used as the source of the PST bus.

Transition operations

Operate transitions using the transition area on the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4.

1

Press the button.

f

Select the transition target.
Multiple targets can be selected by pressing the /// buttons simultaneously.

2

Select the transition type.

f

Use the transition type selection buttons. (page 25)

3

Execute the transition using the fader lever or the transition execution button.

Manual transition

Move the fader lever to execute the transition.

Auto transition

Press the button to execute the transition automatically.

Cut transition

Press the button to execute the transition instantaneously.