Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) - Manual (Page 125)

– 125 –
Chapter 6 Input/Output Signal Settings — Setting output signals
Setting output signals
[SDI OUT 1] to [SDI OUT 16] are used for SDI signal output.
The functions differ depending on the output signals.
@ @ NOTE
t There is a limitation on the function when the switcher mode is set to the 3G mode or the 4K mode. For details on the 3G mode or the 4K mode, refer
to “Difference of function for each mode” (page 164).
r List of settings by output signal
f “ l ” indicates enabled, and “―” indicates disabled.
[Assign] Color corrector* [Down Converter]
[SDI OUT 1] - [SDI OUT 12] l ― ―
[SDI OUT 13], [SDI OUT 15] l l ―
[SDI OUT 14], [SDI OUT 16] l l l
* For details, refer to “Color corrector” (page 86).
Assigning output signals
Assign output signals to [SDI OUT 1] through [SDI OUT 16].
1
Select the button → [SDI OUT] → [Assign] tab.
2
Set the output signals to assign.
f Output signals that can be assigned are as follows.
ME1PGM, ME2PGM, DSKPGM1,
DSKPGM2
Outputs an image with the wipe, mix, key, downstream key or other effect to the switcher's main line output.
DSKPVW1, DSKPVW2 Outputs the DSK preview signal with the ME1PVW or ME2PVW output signal in background.
AUX1 ‑ AUX16 Outputs the signal selected by the 16 lines of AUX buses ([AUX1] to [AUX16]).
ME1CLN, ME2CLN, DSK1CLN,
DSK2CLN, DSK3CLN, DSK4CLN
Outputs clean signals before key effects were added. ME1CLN and ME2CLN signals can be switched to the Key Out
signals which are used for key combination.
MV1 ‑ MV4
Outputs the MultiView display signal. Multiple input and output signals are reduced and output to a single screen.
(page 127)
ME1KEYPVW, ME2KEYPVW,
SEL KEYPVW
Outputs the preview signal exclusively for the key.
ME1PVW, ME2PVW Outputs the preview signals for BKGD, KEY1 to KEY4 which were selected in the next transition.
f For details on ME/DSK output signal settings, refer to “Setting the ME output and DSK output” (page 148).
Setting the down‑converter
For [SDI OUT 14], [SDI OUT 16], the down-converter is available.
When the system format is 1080/59.94i, 720/59.94p, the image is output in 480/59.94i format.
When the system format is 1080/50i, 720/50p, the image is output in 576/50i format.
This function cannot be selected when the system format is SD (480/59.94i, 576/50i).
1
Select the button → [SDI OUT] → [Down Converter] tab.
2
Select an item in [Enable] in the [SDI OUT 14]/[SDI OUT 16] column.
[Off] Disables the down-converter.
[On] Enables the down-converter.
3
Select an item in [Limit] in the [SDI OUT 14]/[SDI OUT 16] column.
f Set the color range.
[Off] Does not restrict the color range.
[108%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 108%.
[104%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 104%.
[100%] Restricts the amplitude level of the colors (R, G, and B) to 0% to 100%.
4
Select an item in [Scale] in the [SDI OUT 14]/[SDI OUT 16] column.
f Select the scaling system.