Panasonic AV-HS6000 2 M/E Live Switcher Main Frame & Control Panel (Dual Redundant Power Supplies) - Manual (Page 151)

– 151 –
Chapter 8 System Menu — Setting the Control Panel AV‑HS60C1/AV‑HS60C2/AV‑HS60C4
Setting the Control Panel AV‑HS60C1/AV‑HS60C2/AV‑HS60C4
Settings for the main control panel and sub control panel
Panel brightness and saver time can be set for each of the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4.
Setting the touch buzzer
The buzzer sound during touch screen operation can be enabled/disabled.
f The buzzer only activates when operating the Menu Panel AV-HS60C3.
1
Select the button → [CTRL PANEL] → [Main Panel]/[SubPanel1]/[SubPanel2] tab.
2
Select an item in [Touch Sound] in the [Sound] column.
[Touch Sound] Sets the enable ([On])/disable ([Off]) of the buzzer sound during the touch screen operation in the menu panel.
[Register Sound] Sets the enable ([On])/disable ([Off]) of the buzzer sound during the [Store] operation of the memory.
[Error Sound] Sets the enable ([On])/disable ([Off]) of the buzzer sound when the error message is displayed.
Setting menu delegation
For details on the menu delegation function, refer to “Menu delegation function” (page 45).
Setting the saver time
The panel backlight can be automatically turned off when panel operation becomes idle for a certain period.
f This setting is applied to Menu Panel AV-HS60C3, multi-selection panel, and source name display panel.
1
Select the button → [CTRL PANEL] → [Main Panel]/[SubPanel1]/[SubPanel2] tab.
2
Select an item in [Saver Time] in the [Saver Time] column.
[On] Backlight is turned on all the time.
[Off]
The backlight turns off as soon as [Off] is set. It turns on again when the panel is operated. The setting after it turns on
becomes [On].
[60], [120], [180]
When no control panel operation is performed within a set time interval (60, 120, or 180 minutes), the built-in display
backlight is turned off automatically. It turns on again when the panel is operated.
@ @ NOTE
t The backlight does not turn on even if a mouse is used.
Setting the panel brightness
1
Select the button → [CTRL PANEL] → [Main Panel]/[SubPanel1]/[SubPanel2] tab.
2
Set [MenuPanel] in the [Brightness] column.
f Adjust the brightness of the Menu Panel AV-HS60C3.
3
Set [Select Panel] in the [Brightness] column.
f Adjust the brightness of the multi-selection menu panel.
4
Set [Source Name] in the [Brightness] column.
f Adjust the brightness of the source name display panel.
Setting the button color
The lighting color for each of the Control Panel AV-HS60C1/AV-HS60C2/AV-HS60C4 buttons can be set.
Setting the colors when the buttons are turned on
f You can select [Red], [Green], [Yellow], [Orange], and [ColorGroup1] to [ColorGroup8].
1
Select the button → [CTRL PANEL] → [Button Color] tab.
2
Select an item in [High Tally] in the [Select Button] column.
f Set the color of the button included in the on-air output.
f Applicable buttons are the KEY bus crosspoint buttons, PGM/A bus crosspoint buttons, PST/B bus crosspoint buttons, corresponding buttons from
to , to buttons, and the KEY bus selector buttons (except the button and the
button).
3
Select an item in [Low Tally] in the [Select Button] column.
f Set the color of the button not included in the on-air output (except Preset).
f Besides the KEY bus crosspoint buttons, the PGM/A bus crosspoint buttons, and the PST/B bus crosspoint buttons, other buttons excluding Preset
are also included.