Yaskawa F7 Drive User Manual - Manual (Page 215)

Specifications C - 2
Standard Drive Specifications
The standard Drive specifications are listed in the following tables.
208-240Vac
Table C.1 208-240Vac Drive Specifications
208-240Vac Drives 208-230Vac Drives
Model Number CIMR-
F7U
20P4 20P7 21P5 22P2 23P7 25P5 27P5 2011 2015 2018 2022 2030 2037 2045 2055 2075 2090 2110 *5
Rated output
capacity (kVA)
1.2 1.6 2.7 3.7 5.7 8.8 12.0 17.0 22.0 27.0 32.0 44.0 55.0 69.0 82.0 110.0 130.0 140.0
Horsepower *2 0.5/0.75 1 2 3 5 7.5 10 15 20 25 30 40 50 60 75 100 125 150
Rated output
current (A)
3.2 4.2 7.0 9.6 15.2 23.0 31.0 45.0 58.0 71 85.0 115.0 145.0 180.0 215 283.0 346.0 360.0
Overload capacity *3
(% of rated output
current for 60 sec) 150 138 *3
Current limit (% of
rated output current)
150 138
*3
Carrier frequency *5,*7 2kHz
Maximum output
frequency
300.0Hz
Rated output
capacity (kVA)
1.4 1.8 3.0 4.1 6.4 8.8 12.0 18.0 23.0 29.0 34.0 44.0 62.0 73.0 82.0 120.0 140.0 160.0
Horsepower *2 0.5/0.75 1 2 3 5 7.5 10 15 20 25 30 40 50/60 75 - 100/125 150 -
Rated output
current (A)
3.6 4.6 7.8 10.8 16.8 23.0 31.0 46.2 59.4 74.8 88.0 115.0 162.0 192.0 215 312.0 360.0 415.0
Overload capacity *3
(% of rated output
current for 60 sec.) 107 107 108 107 107 120 120 117 117 114 116 120 107 113 120 109 115 120
Current limit (% of
rated output current)
120
Carrier frequency
(kHz) *6
10 10 10 8 10 15 15 8 10 10 10 10 5 5 8 2 2 2
Maximum output
frequency
400.0Hz
Maximum output
voltage 3-phase; 200, 208, 220, 230, or 240Vac
(Proportional to input voltage)
Rated voltage
Rated frequency
3-phase, 200/208/220/230/240Vac, 50/60Hz 3-phase, 200/208/220/230Vac, 50/60Hz
Rated input current -
Heavy Duty *1 (A)
3.8 4.9 8.4 11.5 18 24 37 52 68 84 94 120 160 198 237 317 381 396
Rated input current -
Normal Duty *1 (A)
4.3 5.5 9.4 13 20 24 37 53 70 89 98 120 180 212 237 350 396 457
Allowable voltage
fluctuation
+ 10%, - 15%
Allowable frequency
fluctuation
±5%
Measures
for power
supply
harmonics
DC
Reactor
Optional Built-in
12-Pulse
Rectification
Not possible Possible *4
*1 The difference between Heavy Duty ratings and the Normal Duty ratings for the Drive are the rated input and output current, overload capacity, carrier frequency, current limit, and maxi-
mum output frequency. Parameter C6-01 must be set to value of “0” for Heavy Duty ratings and “2” for Normal Duty ratings. Factory default is Heavy Duty (C6-01=0).
*2 Horsepower ratings are based on 230V or 460V NEC Table 430.150. The maximum applicable motor output is given for a standard 4-pole motor. When selecting the actual motor and Drive,
be sure that the Drive's rated output current is appropriate for the motor's rated current.
*3 Model 2110 has an overload rating of 138% of rated output current for 60 seconds and a current limit rating of 138%. Models 4220 and 4300 have an overload rating of 150% of rated output
current for 45 seconds and a current limit rating of 150%.
*4 When setting the carrier frequency above the factory default, the Drive must be derated.
*5 Heavy Duty ratings for models 2110, 4220 and 4300 are effective in software version VSF103021 and higher.
*6 Each value shown is the Maximum carrier frequency and default carrier frequency.
*7 The carrier frequency for Heavy Duty is default to 2 kHz. Software version VSF103021 and higher may allow the carrier frequency to be increased above 2 kHz with a reduction in
continuous rated output current. Refer to C6-02 in Chapter 5 for further details.
O
u
tpu
t rat
ing
s
Hea
v
y Duty
*
1
Norma
l Duty
*
1
Pow
er s
u
pp
ly c
h
ar
act
er
ist
ics
C
ont
ro
l c
h
arac
te
ri
st
ics