Yaskawa F7 Drive User Manual - Manual (Page 185)

Parameters A - 20
DI-08, 16 Setup
F3-01
DI-08 / DI-16H2 Input
Selection
DI Input
Sets the function of the DI-08 or the DI-16H2 digital input option
board.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1Hz unit
4: BCD 0.1Hz unit
5: BCD 0.01Hz unit
6: BCD (5-digit) 0.01Hz unit (only effective when DI-16H2 is
used.)
7: Binary input
When o1-03 is set to 2 or higher, the input will be BCD, and the
units will change to the o1-03 setting.
0 to 7 0 A A A A
AO-08, 12 Setup
F4-01
AO-08/AO-12 Channel 1
Monitor Selection
AO Ch1 Sel Sets the number of the monitor item to be output. (U1- )
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 35, 39, 40, 41. 1 to 45 2 A A A A
F4-02
AO-08/AO-12 Channel 1
Gain
AO Ch1 Gain
Sets the channel 1 gain.
Ex: Set F4-02 = 50% to output 100% at 5.0V output. 0.0 to
1000.0
100.0% A A A A
F4-03
AO-08/AO-12 Channel 2
Monitor Selection
AO Ch2 Sel Sets the number of the monitor item to be output. (U1- )
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 39, 40, 41.
1 to 45 3 A A A A
F4-04
AO-08/AO-12 Channel 2
Gain
AO Ch2 Gain
Sets the channel 2 gain.
Ex: Set F4-04 = 50% to output 100% at 5.0V output. 0.0 to
1000.0
50.0% A A A A
F4-05
AO-08/AO-12 Channel 1 Out-
put Bias
AO Ch1 Bias
Sets the channel 1 bias (100%/10V).
Ex: Set F4-05 = 50% to output 0% at 5.0V output. -110.0 to
110.0
0.0% A A A A
F4-06
AO-08/AO-12 Channel 2 Out-
put Bias
AO Ch2 Bias
Sets the channel 2 bias (100%/10V).
Ex: Set F4-06 = 50% to output 0% at 5.0V output. -110.0 to
110.0
0.0% A A A A
F4-07
AO-12 Channel 1 Signal
Level
AO Opt Level Ch1 Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
0 to 1 0 A A A A
F4-08
AO-12 Channel 2 Signal
Level
AO Opt Level Ch2 Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
0 to 1
0 A A A A
DO-02, 08 Setup
F5-01
DO-02/DO-08 Channel 1 Out-
put Selection
DO Ch1 Select Sets the digital output function number for channel 1. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 0 A A A A
F5-02
DO-02/DO-08 Channel 2 Out-
put Selection
DO Ch2 Select Sets the digital output function number for channel 2. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 1 A A A A
F5-03
DO-08 Channel 3 Output
Selection
DO Ch3 Select Sets the digital output function number for channel 3. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 2 A A A A
F5-04
DO-08 Channel 4 Output
Selection
DO Ch4 Select Sets the digital output function number for channel 4. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 4 A A A A
F5-05
DO-08 Channel 5 Output
Selection
DO Ch5 Select Sets the digital output function number for channel 5. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 6 A A A A
F5-06
DO-08 Channel 6 Output
Selection
DO Ch6 Select Sets the digital output function number for channel 6. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 37 A A A A
F5-07
DO-08 Channel 7 Output
Selection
DO Ch7 Select Sets the digital output function number for channel 7. See the H2
parameter group for possible selections.
Effective when digital output card DO-02 or DO-08 is used.
0 to 38 F A A A A
Denotes that parameter can be changed when the Drive is running.
Table A.1 F7 Parameter List (Continued)
Parameter
No.
Parameter Name
Digital Operator Display
Description
Setting
Range
Factory
Setting
Control Method
V/F
V/F
w/PG
Open
Loop
Vector
Flux
Vector