Hypertherm HyIntensity Fiber Laser Rev.3 - Manual (Page 159)

setup and OperatiOn
HyIntensity Fiber Laser Instruction Manual – 807090 Revision 3 3-51
Cut charts
•
The cut c
harts show general settings for cutting. Settings may need to be c
hanged for specific conditions and material compositions
•
There are seperate cut c
harts for eac
h type of laser power supply
, 1.0 kW
, 1.5 kW
, 2.0 kW
, and 3.0 kW
Note:
Before cutting, check all settings and adjustments and check for damaged parts and worn consumables.
HFL010 (1.0 kW) Mild Steel* cut chart - Metric
thickness
Nozzle
Pierce Parameters
Cut Parameters
mm
Size and
Type (mm)
Part
Number
Extension
(mm)
Height (mm)
Duty Cycle (%)
Time (sec)
Pressure
(bar)
Creep T
ime (sec)
Pressure
(bar)
Height (mm)
Kerf (mm)
Power (W)
Feedrate (mmpm)
Marking all thic
knesses
0.0
1
3
0
15
0
38
10
0.5
1.0
021
09
6
20
1.5
10
0
0.2
2.00
0.1
5
1
0.2
1000
11
000
1.0
1.0
021
09
6
20
1.5
10
0
0.2
2.00
0.1
5
1
0.2
1000
880
0
1.5
1.0
021
09
6
20
1.5
10
0
0.2
2.00
0.1
5
1
0.2
1000
7000
2.0
1.0
021
09
6
20
1.5
10
0
0.2
2.00
0.1
5
1
0.2
1000
444
5
2.5
1.0
021
09
6
24
3.0
10
0
0.5
0.55
0.1
0.55
1
0.35
1000
29
00
3.0
1.0
021
09
6
23
3.0
10
0
0.5
0.55
0.2
0.55
1
0.35
1000
24
00
3.5
1.0
021
09
6
23
3.0
10
0
0.5
0.55
0.2
0.55
1
0.35
1000
2000
4.0
D1.2
0211
02
23
3.0
10
0
0.5
0.55
0.2
0.55
1
0.35
1000
18
00
5.0
D1.2
0211
02
23
3.0
10
0
0.5
0.55
0.2
0.55
1
0.35
1000
15
00
6.0
D1.5
0211
03
23
4.5
90
2.0
0.5
0
0.2
0.55
1
0.35
1000
115
0
8.0
D1.5
0211
03
23
4.5
90
3.0
0.5
0
0.3
0.55
1
0.35
1000
925
9.0
D2.0
0211
04
23
5.0
90
4.0
0.5
0
0.3
0.55
1
0.35
1000
825
10.0
D2.0
0211
04
23
5.0
90
4.0
0.5
0
0.5
0.55
1
0.35
1000
75
0
D = Dual flow nozzle * Oxygen assist gas