Hypertherm HyIntensity Fiber Laser Rev.3 User Manual
Page 125
setup and OperatiOn
HyIntensity Fiber Laser
Instruction Manual – 807090 Revision 3
3-17
Note: This process can also be followed to verify the parameters for Comb Test, MPA Display, and PWM Display by
selecting each one and comparing the value on the screen with the table on page 3-21
Push to Select
+
=
Setups
screen
+
=
Hypernet
highlighted
Push to Select
+
=
Hypernet
selected
+
=
selected
+
=
Hypernet
On/Off
Continued from the previous page
Caution: the values on the
and should not be changed without instructions from the factory or from
a Hypertherm technician.
Comb Quad
x.x
Comb Slope
x.x
Comb Offset
x.x
Comb Quad
x.x
Comb Slope
x.x
Comb Offset
x.x
Hypernet
OFF
MPA Display
OFF
Comb Test
ON
PWM Display
OFF
Hypernet
OFF
MPA Display
OFF
Comb Test
ON
PWM Display
OFF
Hypernet
OFF
MPA Display
OFF
Comb Test
ON
PWM Display
OFF
- EDGE Pro Ti Shape Cutting Control Rev.2 (288 pages)
- 80669J Rev.3 (304 pages)
- HD3070 Plasma Arc Cutting System w/ Manual Gas Console (281 pages)
- MAXPRO200 Rev.2 (294 pages)
- MicroEDGE Pro Shape Cutting Control Rev.2 (182 pages)
- HPR260 Auto Gas Preventive Maintenance Program Rev.4 (288 pages)
- Powermax1650 (317 pages)
- Shape Cutting Control (66 pages)
- PHC Sensor (58 pages)
- HTA Rev 6.00 Operators Manual (212 pages)
- HTA Rev 7.00 Install Guide (242 pages)
- THC Control Board Replacement (13 pages)
- THC Plasma Interfacer Upgrade (9 pages)
- THC X-Y Table Product Configuration (20 pages)
- D845GERG2 (128 pages)
- MRT2 (64 pages)
- MRT (98 pages)
- Duramax Hyamp Long Handheld Torches (92 pages)
- Duramax Hyamp Robotic Torch (74 pages)
- PCBS-0124 (70 pages)
- SuperMicro 370SBA 533Mhz (90 pages)
- LR2075 (56 pages)
- Phoenix 8.0 (585 pages)
- LH2125 (60 pages)
- HD3070 w/ Automatic Gas (35 pages)
- HD3070 w/Manual Gas (43 pages)
- HD4070 Rev.8 (278 pages)
- HD4070 Product Configuration (88 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (33 pages)
- HPR800XD Manual Gas Preventive Maintenance Program Rev.1 (32 pages)
- HPR800XD Manual Gas Rev.2 (368 pages)
- HPRXD Short Torch with Integrated Lead Rev.1 (30 pages)
- HT4001 (59 pages)
- DuraChill 5 HP Air-Cooled Chiller For Hypertherm (29 pages)
- HT4001 Air Injected Water Muffler System (40 pages)
- H601 Power Supplies (62 pages)
- MAX200 Remote Switch (9 pages)
- HT4100 Plasma Arc Cutting System Operating (50 pages)
- HT4001 Plasma Arc Cutting System (259 pages)
- HSD130 HySpeed Plasma (233 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.7 (53 pages)
- HySpeed HT2000 Plasma Arc Cutting System Rev.27 (289 pages)
- MAX200 Water Muffler (39 pages)
- HT2000LHF Product Configuration (23 pages)