1 ip_fax device – FaxBack NET SatisFAXtion 8.6 - Manual User Manual
Page 226

4 – Appendices
NET SatisFAXtion 8.6 Manual
226
minimum time between dials across all channels. In effect this limits the calls-
per-second to 1000 ÷ sip_invite_delay_msecs. A value of 0 imposes no artificial
rate limit and IP_Fax will send calls as fast as possible. Default:
100
.
sip_retr y_invite_count [dword 0–1000]: This is the max number of times to
retry for a when doing the
sip_retry_invite_error_numbers
logic. Default:
20
.
sip_retr y_invite_delay_msecs [dword 0–1000]: This is the time to wait
between sip_retry_invite_error_numbers retries. Default:
500
.
sip_retr y_invite_error_numbers [string]: Some services return an error if
they are busy and if the
INVITE
is sent again within a short period, it should
succeed. This is a list of the error that and
INVITE
should be repeated for. This is
a list of comma separated IP_FAX error numbers (not SIP response codes)
Format: comma separated list of hexadecimal numbers. Default:
28675,28496
.
star t_por t_number [dword 1–65535]: First UDP port to allocate for RTP and
T.38. Default:
49152
.
t38_fax_max_buffer [dword 0–65535]: Buffer size to specify in the
a=T38FaxMaxBuffer
SDP attribute. Default:
200
.
t38_fax_max_datagram [dword 0–65535]: Datagram size to specify in the
a=T38FaxMaxDatagram
SDP attribute. Default:
72
.
t38_control_redundancy [dword 0–65535]: Levels of redundant data to
include in each T.38 “low speed” control packet. Default: 5.
t38_image_redundancy [dword 0–65535]: Levels of redundant data to
include in each T.38 “high speed” image packet. Default: 2.
t38_qos_token_rate [dword 0–65535]: TokenRate of sending T.38 RSVP
FlowSpec. Default:
9250
.
t38_qos_peak_bandwidth [dword 0–65535]: PeakBandwidth of sending
T.38 RSVP FlowSpec. Default:
13875
.
t38_qos_token_bucket_size [dword 0–65535]: TokenBucketSize of
sending T.38 RSVP FlowSpec. Default:
680
.
t38_qos_latency [string]: Latency of sending T.38 RSVP FlowSpec. Default:
QOS_NOT_SPECIFIED
.
t38_qos_delay_variation [string]: DelayVariation of sending T.38 RSVP
FlowSpec. Default:
QOS_NOT_SPECIFIED
.
t38_qos_service_type [string]: ServiceType of sending T.38 RSVP FlowSpec.
Default:
SERVICETYPE_GUARANTEED
.
t38_qos_max_sdu_size [dword 0–65535]: MaxSduSize of sending T.38
RSVP FlowSpec. Default:
340
.
t38_qos_minimum_policed_size [dword 0–65535]: MinimumPolicedSize
of sending T.38 RSVP FlowSpec. Default:
340
.
4.2.1.5.1
IP_FAX Device
allowed_receive_baud_rates [string]: This setting constrains a modem to
use only certain baud rates. Use this to block a modem from using a rate or
rates that it supports, but are unreliable in your environment or are undesirable
for some other reason. On transmitting, use this as a mask; the modem will use