6 selecting the clean printer tab, Selecting the clean printer tab, Figure 3 - clean printer – HID HDPii Plus User Guide 2.0 User Manual
Page 23
HDP5000 & HDPii Card Printer Encoder User Guide_L000950, 2.0
December 2012
Page 23 of 103
© 2012 HID Global Corporation. All rights reserved.
3.6
Selecting the Clean Printer tab
To clean the printer, follow the instructions outlined on the
Clean Printer tab.
Figure 3 - Clean Printer
•
Clean button: Launches cleaning routine. Follow the instructions to set up the Printer.
•
Help button: Launches help specific to the Clean Printer tab.
Step
Procedure
1
Click the
Clean Printer tab.
a. Remove the Card, InTM Film and Laminate Cartridges and close the covers.
b. Remove the paper back from both sides of the Cleaning Card. (
Note: DO NOT
remove the left liner if a Magnetic Encoding Module is installed in your printer.)
c. Insert the Cleaning Card into the Card Hopper’s infeed rollers.
d. Click
Clean button.
e. Guide the Cleaning Card into the Printer as needed.
f. When the Cleaning routine is complete, the Cleaning Card exits the Printer.
g. Reinstall the Card, InTM Film and Laminate Cartridges.
The Cleaning routine begins after completing all current print jobs. Use a standard CR80
sized cleaning card.
- bioCLASS Installation Guide (12 pages)
- Crescendo Integration (54 pages)
- EDGE EVO EDM-M Door Module Installation Guide (4 pages)
- EDGE EVO EDWM-M Door-Wiegand Module Installation Guide (4 pages)
- EDGE EVO EH400 Hi-O Controller Installation Guide (12 pages)
- EDGE EVO Solo ESH400 Hi-O Controller Installation Guide (12 pages)
- EDGE EVO EH400-K Standard Controller Installation Guide (12 pages)
- EDGE EVO Solo ESHR40 Hi-O Controller/Reader Installation Guide (12 pages)
- EDGE EVO EIM-M Hi-O Input Module Installation Guide (2 pages)
- EDGE EVO EIM-M Input Module Installation Guide (2 pages)
- EDGE EVO ELM Hi-O Lock Module Installation Guide (2 pages)
- EDGE EVO ELM Lock Module Installation Guide (2 pages)
- EDGE EVO EVM Hi-O Voltage Module Installation Guide (2 pages)
- EDGE EVO EVM Voltage Module Installation Guide (2 pages)
- EDGE EVO Hi-O Interface Door Module Installation Guide (4 pages)
- EDGE EVO Solo ESH400-K Networked Controller Installation Guide (10 pages)
- EDGE EWM-M Hi-O Wiegand module Installation Guide (4 pages)
- EDGE Plus Installation Guide (2 pages)
- EntryProx Installation Guide (58 pages)
- MIFARE Reader Installation Guide (6 pages)
- Hi-O iCLASS Installation Guide (49 pages)
- iCLASS Keypad Installation Guide (12 pages)
- iCLASS R Installation Guide (12 pages)
- iCLASS RK Series Rev C Installation Guide (12 pages)
- iCLASS SE Installation Guide (10 pages)
- iCLASS SE/ multiClass SE Installation Guide (10 pages)
- Magnetic Stripe / Prox Reader 230 and 240 Installation Guide (2 pages)
- Magnetic Stripe Reader 644 Installation Guide (2 pages)
- Magnetic Stripe Reader 740 Installation Guide (2 pages)
- Magnetic Stripe Reader 780 Installation Guide (2 pages)
- MaxiProx Installation Guide (19 pages)
- multiCLASS / Magnetic Stripe Installation Guide (12 pages)
- multiCLASS / Magnetic Stripe with Keypad Installation Guide (10 pages)
- multiCLASS RP Series Hi-O Installation Guide (6 pages)
- pivClass Installation Guide (8 pages)
- Prox Programmer Installation Guide (21 pages)
- ProxPass Installation Guide (3 pages)
- ProxPoint Installation Guide (3 pages)
- ProxPoint Plus Installation Guide (2 pages)
- ProxPro II Installation Guide (2 pages)
- ProxPro Installation Guide (14 pages)
- Serial ProxPro Reader Installation Guide (10 pages)
- SmartID Mounting Plate Installation Guide (2 pages)
- SmartID Spacer Installation Guide (2 pages)
- VertX EVO V1000 Installation Guide (19 pages)