HID Magnetic Stripe Reader 780 Installation Guide User Manual
Specifications, Regulatory, General
Specifications
INPUT:
Magnetic Stripe Cards, high or low coercivity, EMPI I,
EMPI II or ANSI format, up to 14 characters.
CARD SIZE:
CR-80, 2.125" x 3.375" x .030", Track 1, 2, and 3
(53.97 mm x 85.73 mm x 0.762 mm)
OUTPUT:
Standard Wiegand 5-wire format with optional second
LED control line. Optional "Clock-and-Data" format.
DISTANCE:
200 feet (61 m) with #22 AWG wire
500 feet (53 m) with #18 AWG wire
TEMPERATURE RANGE:
-35 to +66°s C (-31 to 150° F).
POWER:
12 VDC, 0.25 W
READ SPEED:
5 to 50 IPS on withdrawal
DIMENSIONS:
Reader; 6.75" H x 5.25" W x 2.75" D.
(17.14 mm x 13.33 mm x 6.98 mm)
LED:
Two Colors - Red and Green; Optional Amber
Regulatory
FCC
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
UL
This Proximity Reader is intended to be powered from a limited
power source output of a previously certified power supply. This
Reader is intended to be used with UL 294 Listed Control
Equipment.
CE Marking
HID Global hereby declares that this proximity reader is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
P/N 2280-3738, Rev C
July 2, 2007
Parts List
Card Reader kit consists of:
3110-7801 3110-7802
1-Reader assembly
1-Reader assembly
1-Installation Kit 2270-0780
• 6 Wire Cable Connector
assembly
• Four 6-32 x 7/8" machine
screws
• Four #6 standard
washers
• Tamper switch assembly
1-Installation Kit 2270-0780
• 6 Wire Cable Connector
assembly
• Four 6-32 x 7/8" machine
screws
• Four #6 standard
washers
• Tamper switch assembly
1-Instructions 2280-3738
1-Instructions 2280-3738
1-Instructions
2270-4189
General
The Model 780 is a Ruggedized pass-through card reader with a
keypad. The 12-Volt powered reader is fully weatherproof. The
reader accepts both EMPI and ABA format cards and reports both
card and keypad data in a variety of output formats. Three LED's
prompt the user for appropriate action.
A label located on the internal, rear surface carries part
designations. The reader part number used when ordering is
3110-7801 or 3110-7802. Available in black only.
The Model 3110-7801 is designed for both indoor, and outdoor
use.
Mounting
The card reader mounts on a single or double-gang electrical
'handy box' with conventional #6-32 machine screws. The vertical
spacing of the mounting screws is 3.25" (8.25 cm) and for a
double-gang handy box the horizontal spacing is 1.8125" (4.6 cm)
The reader is secured to its mounting plate with 2 tamper-proof
screws, the supplied screws are #8-32 x 0.675" oval head screws.
The driver is a #8 AVSAFE driver, P/N 1180-0040 and is
manufactured by;
AVDEL
Corporation
50 Lackawanna Avenue
Parsippany, NJ 07054
(201)
263-8100
AVDEL PN# ASMD-0080-7750
If our choice of tamper screws is inconvenient, they may be
replaced by another brand or by #8 round head machine screws.
9292 Jeronimo Road
Irvine, CA 92618
Voice (800)-237-7769
Fax (949)-598-1690
3110-7801 Model 780 Ruggedized P/T
Reader w/keypad
3110-7802
Model 780 Ruggedized P/T
Reader w/Heater Bar
3110-780X Model 780 Ruggedized P/T
Reader w/Custom Firmware
intern
Installation Guide
© 2007 HID Global Corporation. All rights reserved
.
Track Selection
Readers are shipped reading the track II physical location. If your
card is coded on track 1, disassemble the read head assembly
and rotate the reading head 180 degrees.
Setup
WARNING
To prevent damage to equipment, make all
connections with the power "OFF" and the
connector unplugged from the reader.
The Model 780 comes assembled from the factory. Located in
the box with the reader you will find the pigtail connector, which is
used to connect the reader to the external wiring.
The reader assembly is designed to be mounted vertically with the
tamper resistant oval head screws facing the floor. Typically, the
recommended reader height from the floor to the bottom of the
reader assembly is 55 inches (1.3 m), however, user convenience
is the determination factor.
The Lexan card slot which is part of the reader assembly is
reversible to allow the card slot angle to match the natural angle
of the wrist when holding the card during pass-through reading.
As an example, if the reader assembly is mounted on the right
side of a door, the card slot angle should point right or away from
the door. If mounted on the left side, the slot points left.
To change the card slot angle, remove the four screws holding the
back plate to the reader assembly and remove the back plate.
Remove the two screws holding the lexan card slot to the reader
assembly and carefully remove the slot so as not to damage the
connected read head wires. Rotate the card slot and plastic
shield 180
° and reassemble.