HID EDGE EVO Solo ESH400-K Networked Controller Installation Guide - Manual

EDGE EVO is the next evolution in access control hardware solutions. A true IP solution that meets the demands of open architecture,
IP-centric environments, EDGE EVO provides fully distributed intelligence and decision making right to the door, leveraging the IT
infrastructure to the maximum extent possible. Leveraging Power-over-Ethernet (PoE), EDGE EVO reduces door installation costs by not
requiring a separate local power supply under many circumstances.
The Standard Networked Controller is a fully integrated single-door controller offering discrete I/O and Wiegand/Clock-and-Data interfaces
to readers. Additionally, connect native Hi-O devices (readers, locks, pushbuttons) and EDGE EVO Hi-O Modules to the Hi-O bus,
providing secure communication around the door. Hi-O involves devices with built-in intelligence and a CANbus that links all the devices
together. Password protect or encrypt Hi-O CANbus data traffic. Each Hi-O device (such as the REX switch, electric strike, card reader and
door operator) is connected to the CANbus by a single, four-wire cable. Two of the wires supply power and the other two are used for data
communication.
Specifications
CONDITIONS VOLTAGE DC (VDC)
CURRENT
(Amp)
POWER (W)
OPERATING
TEMPERTURE CABLE LENGTH
UL REF
NUMBER
Input
DC Input (NSC)
+12VDC 0.18Amp 2.16
32° - 122°F
(0° - 50° C)
Hi-O CAN Bus Total Length 100 ft (30 m) -
22 AWG ● 0.65mm ● 0.33mm 2
Maximum between drops
30 ft (10 m)
22 AWG ● 0.65mm ● 0.33mm 2
RJ45 328 ft (100 m) - Category 5 K
KE400CX
1
X
2
N
+24VDC 0.14Amp 3.36
PoE
(+48VDC NOM)
.085Amp 4.08
DC Input (MAX)
+12VDC 1.5Amp 18.00
+24VDC 1.5Amp 36.00
PoE
(+48VDC NOM)
0.3Amp 14.40
Supervised inputs
(AC, Batt, REX, Door Mon) (MAX)
0-+5VDC Reference
0.005Amp
(sink)
0.025
Data 1/CLK , Data 0 / Data (MAX) 0-+5VDC Reference N/A N/A
Output
GRN LED, RED LED, Beep,
Hold (MAX)
0-+5VDC reference
0.005Amp
(sink)
0.025
External Tamper (MAX) +5VDC (NOM) 0.02 0.100
CAN DC
Output
(MAX) AUX 12 / 24VDC Input +10.8 to +24VDC 1.2Amp * 28.80
PoE Input + 24VDC (NOM) 0.4Amp * 9.60
Reader
DC PWR
Output
(MAX)
AUX 12 VDC +9.8 to +12.25VDC 0.32Amp * 3.92
AUX 24VDC +9.8 to +12.25VDC 0.60Amp * 7.35
PoE Input +9.8 to +12.25VDC 0.58Amp * 7.11
Strike***
/ AUX
Relays
NC or NO
DC Output
(MAX)
AUX 12VDC
Input Unregulated (Wet)
Jumpers
+10 to +12VDC 0.70Amp * 8.40
AUX 24VDC
Input
Unregulated (Wet)
Jumpers
+23 to +24VDC 0.70Amp * 16.80
Regulated (Wet)
Jumpers - 12VDC
+10 to +12VDC 0.70Amp * 8.40
PoE Input
Unregulated (Wet)
Jumpers
+16.5 to +24VDC 0.36Amp * 8.64
Regulated (Wet)
Jumpers - 12VDC
+10 to +12VDC 0.58Amp * 6.96
AUX / PoE
Input Jumpers Set
to Dry +12 to +24VDC
External
2.00Amp ** 48.00
NSC = Normal Standby Condition
* Combined output rating not to exceed V*I = W
1.2 Amp (+24VDC AUX Input, 28.8 W)
1.2 Amp (+12VDC AUX Input, 12.96 W)
EDGE EVO ®
Standard Networked Controller
EH400-K / ESH400-K
I
nstallatIon
G
uIde
82000-921, Rev D.1
October 2012
© 2009 - 2012 HID Global Corporation. All rights reserved.
15370 Barranca Parkway
Irvine, CA 92618-2215
USA
** Each relay
*** Shared between relays.
X
1
= K for Black
G for Gray
X
2
= N for non-Solo
S for Solo