HID Magnetic Stripe Reader 644 Installation Guide - Manual

Specifications
INPUT;
Magnetic Stripe Cards, high or low coercivity, EMPI I, EMPI II or
ABA format.
CARD SIZE:
CR-80, 2.125" x 3.375" x .030", Track 1 or 2
(53.97mm x 85.73 mm x 0.762 mm)
CR-60, 2.328" x 3.250" x .030", Track 1 or 2
(59.13 mm x 82.55 mm x 0.762 mm)
OUTPUT:
Standard Wiegand 5-wire format with optional second LED
control line.
DISTANCE:
200 feet (61 m) with #22 AWG wire (0.325 mm)
500 feet (153 m) with #18 AWG wire (0.823 mm)
TEMPERATURE RANGE:
-31
° to 150°F (-35° to +66°C)
POWER:
35 mA at 5 VDC
READ SPEED:
8 to 50 IPS in either direction.
DIMENSIONS:
Reader : 6.00" (L) x 1.35" (H) x 1.75" (W)
(152.4 mm x 34.29 mm x 44.45 mm)
Adapter Plate: 7.00" (L) x 2.75" (W)
(177.80 mm x 69.85 mm)
LED:
Two Colors - Red and Green
FCC Compliance Statement:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
P/N: 2280-3961
REV B.2
4/20/04
Card Reader kit consists of:
1-Reader assembly
1-Installation Kit 2270-0018 or 2270-0611
1-Instructions 2280-3961
1-Instructions 2280-4189
(For Heater, Model 6446 or 6447)
General
The Model 644 Pass-Through Reader Card Reader reads
magnetic stripe cards that have been encoded with EMPI I or
EMPI II encrypted card numbering format or standard ABA
numbering format.
Cards are read in either direction and the information
transmitted to any host access controller that can supply a 5
VDC operating voltage to the reader, and that can accept the
standard Wiegand 26 or 34-bit format or Clock and Data format.
The card reading slot of the Model 644 Reader is set at an
angle to match the natural angle of the wrist when holding a
card. This angle must be considered when mounting the reader
for maximum user convenience.
The reader can be wall or door frame mounted, horizontal or
vertical, to suit the user.
The 644 card readers are weather resistant, although they
should be mounted to preclude ice build up. The 6446 and
6447 have a heater bar to help prevent ice build up.
The 644-S Custom Reader will have a prom that will read a
custom ABA format
. Before Installing
1.
Reader installation and wiring must conform to applicable
local codes, ordinances, and regulations.
2. The host controller must supply 5 VDC operating voltage
to the reader. The voltage as measured at the reader
must be between 3.2 to 5.5 VDC.
3. The maximum recommended reader distance from the
host is:
200 feet (61 m) with #22 AWG 6-wire cable
500 feet (153 m) with #18 AWG 6-wire cable
Unshielded wire is acceptable, however some host
controllers require tighter standards.
4. Reader options are selected by a rotary switch located on
the front of the reader circuit board.
5. With EMPI cards, the proper 8 or 16-bit "Comparison
Number" must be entered into memory of the host access
controller (similar to a site or facility code). These
numbers, as well as the "Job Code" number used when
reordering EMPI Cards, will be found printed on the label
of your EMPI Card carton. Details are found in the
Comparison Number Check Section.
† 3110-6444 W/P P /T Reader, White
† 3110-6445 W/P P /T Reader, Black
† 3110-6446 W/P P /T W/heater bar Reader, White
† 3110-6447 W/P P /T W/heater bar Reader, Black
† 3110-6448 W/P P /T Connectorized Reader, White
† 3110-6449 W/P P /T Connectorized Reader, Black
9292 Jeronimo Road
Irvine, CA 92618
Voice (800)-237-7769
Fax (949)-598-1690
email: [email protected]
internet: www.HIDcorp.com
Mounting
1. Mount the reader either horizontally or vertically on:
Š A single-gang handy box.
Š A flat surface (wall, etc.) with or without the
adapter plate.
Š On a structural door frame (mullion).
2. When mounting, consider the angle of the reader card slot
in relationship to the natural angle of the wrist when holding
the card. This usually means the card slot points away from
the door. As an example, if mounted on the right side of a
door the slot points right of away from the door. If mounted
on the left the card slot points left. On a horizontal
mounting, the card slot can point either up or down
dependent upon user convenience and height from the floor.
Typical mounting and recommended reader height from the
floor is shown in FIG 1.
55”
55”
60”
Figure
1
3. The reader base plate determines which direction the
reader card slot will point. If the reader base plate is
mounted with its release latch down, the reader card slot
will point left. If mounted up, the reader slot points right.