Watlow EZ-ZONE RMH User Manual
Page 79
Watlow EZ-ZONE
®
RMH Module
•
76
•
Chapter 4 Setup Page
RM High Density Module
•
Setup Page
Display
Parameter Name
Description
Range
Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Profibus
Index
Parameter
ID
Data
Type
&
Read/
Write
[`S2;A]
[ SZ.A]
Timer (1 to 4)
Source Zone A
Set the zone of the function
selected above.
0 to 16
0
13188
[offset 50]
0x83 (131)
1 to 24
5
- - - -
31005
uint
RWES
[sas;A]
[SAS.A]
Timer (1 to 4)
Source Active State A
Set what state will be read
as on.
[high]
High (37)
[LoW]
Low (53)
High
13200
[offset 50]
0x83 (131)
1 to 24
0xB (11)
- - - -
31011
uint
RWES
[SFn;B]
[SFn.b]
Timer (1 to 24)
Source Function B
Set the type of function
that will be used to reset
a retentive timer (reset
signal).
[nonE]
None (61)
[ALM]
Alarm Reset (6)
[`CPE]
Compare (230)
[`Ctr]
Counter (231)
[`dio]
Digital I/O (1142)
[Ent;A]
Profile Event Out A
(233)
[Ent;b]
Profile Event Out B
(234)
[Ent;C]
Profile Event Out C
(235)
[Ent;d]
Profile Event Out D
(236)
[Ent;E]
Profile Event Out E
(247)
[Ent;F]
Profile Event Out F
(248)
[Ent;g]
Profile Event Out G
(249)
[Ent;h]
Profile Event Out H
(250)
[`FUn]
Function Key (1001)
[`lgC]
Logic (239)
[SoF;1]
Special Function Out-
put 1 (1532)
[SoF;2]
Special Function Out-
put 2 (1533)
[SoF;3]
Special Function Out-
put 3 (1534)
[SoF;4]
Special Function Out-
put 4 (1535)
[tMr]
Timer (244)
[`uAr]
Variable (245)
None
13182
[offset 50]
0x83 (131)
1 to 24
2
- - - -
31002
uint
RWES
[`Si;B]
[ Si.b]
Timer (1 to 24)
Source Instance B
Set the instance of the
function selected above.
1 to 250
1
13186
[offset 50]
0x83 (131)
1 to 24
4
- - - -
31004
uint
RWES
[`S2;B]
[ SZ.b]
Timer (1 to 24)
Source Zone B
Set the zone of the function
selected above.
0 to 16
0
13190
[offset 50]
0x83 (131)
1 to 24
6
- - - -
31006
uint
RWES
Note:
Some values will be rounded off to fit in the four-character display.
Full values can be read with other interfaces.
Note:
If there is only one instance of a menu, no submenus will appear.
** These parameters/prompts are available in these menus with firmware revisions 6.0 and
above.
R: Read
W: Write
E:
EEPROM
S:
User
Set