HEIDENHAIN TNC 128 (77184x-02) User Manual
Tnc 128
Table of contents
Document Outline
- TNC 128
- Controls of the TNC
- Fundamentals
- Contents
- 1 First Steps with the TNC 128
- 2 Introduction
- 3 Programming: Fundamentals, file management
- 3.1 Fundamentals
- 3.2 Opening and entering programs
- 3.3 File manager: Fundamentals
- 3.4 Working with the file manager
- Directories
- Paths
- Overview: Functions of the file manager
- Calling the file manager
- Selecting drives, directories and files
- Creating a new directory
- Creating a new file
- Copying a single file
- Copying files into another directory
- Copying a table
- Copying a directory
- Choosing one of the last files selected
- Deleting a file
- Deleting a directory
- Tagging files
- Renaming a file
- Sorting files
- Additional functions
- Additional tools for management of external file types
- Data transfer to/from an external data medium
- The TNC in a network
- USB devices on the TNC
- 4 Programming: Programming aids
- 5 Programming: Tools
- 6 Programming: Tool movements
- 7 Programming: Subprograms and program section repeats
- 8 Programming: Q Parameters
- 8.1 Principle and overview of functions
- 8.2 Part families—Q parameters in place of numerical values
- 8.3 Describing contours with mathematical functions
- 8.4 Angle functions
- 8.5 Calculation of circles
- 8.6 If-then decisions with Q parameters
- 8.7 Checking and changing Q parameters
- 8.8 Additional functions
- 8.9 Accessing tables with SQL commands
- 8.10 Entering formulas directly
- 8.11 String parameters
- String processing functions
- Assigning string parameters
- Chain-linking string parameters
- Converting a numerical value to a string parameter
- Copying a substring from a string parameter
- Converting a string parameter to a numerical value
- Checking a string parameter
- Finding the length of a string parameter
- Comparing alphabetic sequence
- Reading machine parameters
- 8.12 Preassigned Q parameters
- Values from the PLC: Q100 to Q107
- Active tool radius: Q108
- Tool axis: Q109
- Spindle status: Q110
- Coolant on/off: Q111
- Overlap factor: Q112
- Unit of measurement for dimensions in the program: Q113
- Tool length: Q114
- Coordinates after probing during program run
- Deviation between actual value and nominal value during automatic tool measurement with the TT 130
- 9 Programming: Miscellaneous functions
- 10 Programming: Special functions
- 11 Manual operation and setup
- 11.1 Switch-on, switch-off
- 11.2 Moving the machine axes
- 11.3 Spindle speed S, feed rate F and miscellaneous function M
- 11.4 Datum setting without a 3-D touch probe
- 11.5 Using 3-D touch probes (Touch Probe Functions software option 17)
- 11.6 Calibrating a 3-D touch trigger probe (Touch Probe Functions software option 17)
- 11.7 Datum setting with 3-D touch probe (Touch Probe Functions software option 17)
- 12 Positioning with Manual Data Input
- 13 Test run and program run
- 14 MOD functions
- 14.1 MOD function
- 14.2 Graphic settings
- 14.3 Machine settings
- 14.4 System settings
- 14.5 Position Display Types
- 14.6 Setting the unit of measure
- 14.7 Displaying operating times
- 14.8 Software numbers
- 14.9 Entering the code number
- 14.10 Setting up data interfaces
- Serial interfaces on the TNC 128
- Application
- Setting the RS-232 interface
- Setting the BAUD RATE (baudRate)
- Setting the protocol (protocol)
- Setting data bits (dataBits)
- Check parity (parity)
- Setting the stop bits (stopBits)
- Setting handshaking (flowControl)
- Settings for data transfer with the TNCserver PC software
- Setting the operating mode of the external device (fileSystem)
- Data transfer software
- 14.11 Ethernet interface
- 14.12 Firewall
- 14.13 Load machine configuration
- 15 Cycle fundamentals
- 15.1 Introduction
- 15.2 Available Cycle Groups
- 15.3 Working with fixed cycles
- 15.4 PATTERN DEF pattern definition
- 15.5 POLAR PATTERN (Cycle 220)
- 15.6 LINEAR PATTERN (Cycle 221)
- 15.7 Point tables
- 16 Drilling, boring and thread cycles
- 16.1 Fundamentals
- 16.2 CENTERING (Cycle 240)
- 16.3 DRILLING (Cycle 200)
- 16.4 REAMING (Cycle 201)
- 16.5 BORING (Cycle 202)
- 16.6 UNIVERSAL DRILLING (Cycle 203)
- 16.7 BACK BORING (Cycle 204)
- 16.8 UNIVERSAL PECKING (Cycle 205)
- 16.9 SINGLE-LIP DEEP-HOLE DRILLING (Cycle 241)
- 16.10 Programming Examples
- 16.11 TAPPING with a floating tap holder (Cycle 206)
- 16.12 RIGID TAPPING without a floating tap holder (Cycle 207)
- 16.13 Programming Examples
- 17 Fixed cycles: Pocket milling / stud milling
- 18 Cycles: Coordinate Transformations
- 19 Cycles: Special Functions
- 20 Touch probe cycles
- 20.1 General information about touch probe cycles
- 20.2 Before You Start Working with Touch Probe Cycles
- Maximum traverse to touch point: DIST in touch probe table
- Set-up clearance to touch point: SET_UP in touch probe table
- Orient the infrared touch probe to the programmed probe direction: TRACK in touch probe table
- Touch trigger probe, probing feed rate: F in touch probe table
- Touch trigger probe, rapid traverse for positioning: FMAX
- Touch trigger probe, rapid traverse for positioning: F_PREPOS in touch probe table
- Executing touch probe cycles
- 20.3 Touch probe table
- 20.4 Fundamentals
- 20.5 Calibrate the TT (Cycle 480, Touch Probe Functions software option 17)
- 20.6 Calibrate the wireless TT 449 (Cycle 484, software option 17 Touch Probe Functions software option 17)
- 20.7 Measure the tool length (Cycle 481, software option 17 Touch Probe Functions software option 17)
- 20.8 Measure the tool radius (Cycle 482, software option 17 Touch Probe Functions software option 17)
- 20.9 Measure the tool length and radius (Cycle 483, software option 17 Touch Probe Functions software option 17)
- 21 Tables and overviews
- Index