Touch probe cycles 20.4 fundamentals – HEIDENHAIN TNC 128 (77184x-02) User Manual
Page 480

Touch probe cycles
20.4 Fundamentals
20
480
TNC 128 | User's Manual HEIDENHAIN Conversational Programming | 5/2014
Input examples for common tool types
Tool type
CUT
TT:R_OFFS
TT:L_OFFS
Drill
– (no function)
0 (no offset required
because tool tip is to be
measured)
End mill
with diameter
of < 19 mm
4 (4 teeth)
0 (no offset required
because tool diameter is
smaller than the contact
plate diameter of the TT)
0 (no additional offset
required during radius
measurement. Offset from
offsetToolAxis is used)
End mill
with diameter
of > 19 mm
4 (4 teeth)
R (offset required because
tool diameter is larger than
the contact plate diameter
of the TT)
0 (no additional offset
required during radius
measurement. Offset from
offsetToolAxis is used)
Radius cutter
with a
diameter of 10 mm, for
example
4 (4 teeth)
0 (no offset required
because the south pole of
the ball is to be measured)
5 (always define the tool
radius as the offset so
that the diameter is not
measured in the radius)
- TNC 122 User Manual (63 pages)
- TNC 122 Technical Manual (70 pages)
- TNC 360 Service Manual (157 pages)
- TNC 416 Technical Manual (510 pages)
- TNC 335 Technical Manual (581 pages)
- TNC 360 User Manual (237 pages)
- TNC 360 ISO-Programmierung (2 pages)
- TNC 415 (280 540) User Manual (227 pages)
- TNC 370D (92 pages)
- TNC 416 (289 pages)
- TNC 415 (280 540) Technical Manual (752 pages)
- TNC 415 (259 96x) Service Manual (195 pages)
- TNC 407 (280 580) User Manual (376 pages)
- iTNC 530 (340 420) Pilot (104 pages)
- TNC 407 (280 580) ISO Programming (333 pages)
- TNC 415 (280 540) Service Manual (252 pages)
- PT 880 Installation (112 pages)
- ND 100 User Manual (116 pages)
- ND 287 User Manual (147 pages)
- ND 280 Quick Start (12 pages)
- ND 200 (156 pages)
- ND 282 (10 pages)
- ND 287 Quick Start (26 pages)
- ND 282 B (39 pages)
- ND 281 A (44 pages)
- ND 281 B v.1 (53 pages)
- ND 281 B v.2 (65 pages)
- ND 221 v.2 (10 pages)
- ND 231 B v.2 (56 pages)
- ND 231 B v.1 (44 pages)
- ND 221 B v.2 (45 pages)
- ND 550 v.2 (8 pages)
- NDP 560 (10 pages)
- ND 523 (93 pages)
- ND 570 (8 pages)
- ND 750 v.2 (46 pages)
- ND 760 v.3 (72 pages)
- ND 770 v.1 (40 pages)
- ND 770 v.3 (41 pages)
- ND 760 E (44 pages)
- IOB 49 (21 pages)
- NDP 960 (68 pages)
- ND 780 Installation (132 pages)
- ND 970 (47 pages)
- ND 1100 Quick Start (36 pages)