Comtech EF Data CIM-300L - Manual (Page 115)

CiM-300L IP Enabled Satellite Modem Rev. 1
Serial Remote Control CD/CIM300L.IOM
89
Bulk Consol.
Status
(continued)
Parameter
Number Parameter Name
(Command Reference)
Description
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 4)
(Note 4)
(Note 4)
(Note 4)
(Note 5)
(Note 6)
(Note 5)
(Note 6)
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
Demodulator Spectrum Rotation
(ref. 'DSR_' command).
Reed-Solomon Encoder Enable
(ref. 'RSEN_' command).
Reed-Solomon Decoder Enable
(ref. 'RSDE_' command).
Backward Alarm enable TX1
(ref. 'BW_TX1_' command).
Backward Alarm enable TX2
(ref. 'BW_TX2_' command).
Backward Alarm enable
(ref. 'BW_TX3_' command).
Backward Alarm enable TX4
(ref. 'BW_TX4_' command).
Backward Alarm enable RX1
(ref. 'BW_RX1_' command).
Backward Alarm enable RX2
(ref. 'BW_RX2_' command).
Backward Alarm enable RX3
(ref. 'BW_RX3_' command).
Backward Alarm enable RX4
(ref. 'BW_RX4_' command).
TX Driver Type
(ref. 'TXDR_' command).
RX Driver Type
(ref. 'RXDR_' command).
reserved null field.
ASYNC TX Overhead Baud Rate
(ref. 'TOBR_' command).
ASYNC RX Overhead Baud Rate
(ref. 'ROBR_' command).
ASYNC TX Channel Char. Length
(ref. 'TCCL_' command).
ASYNC RX Channel Char. Length
(ref. 'RCCL_' command).
p71 = n, where 'n' is '0' (NRM), '1' (INV).
p72 = n, where 'n' is '0' (off) or '1' (on).
p73 = n, where 'n' is '0'(OFF), '1' (ON), '2' (CORR_OFF).
p74 = n, where 'n' is '0' (off) or '1' (on).
p75 = n, where 'n' is '0' (off) or '1' (on).
p76 = n, where 'n' is '0' (off) or '1' (on).
p77 = n, where 'n' is '0' (off) or '1' (on).
p78 = n, where 'n' is '0' (off) or '1' (on).
p79 = n, where 'n' is '0' (off) or '1' (on).
p80 = n, where 'n' is '0' (off) or '1' (on).
p81 = n, where 'n' is '0' (off) or '1' (on).
p82 = n, where 'n' is '0' (G.703), '1' (V.35), '2' (RS422), or '3'
(RS232).
p83 = n, where 'n' is '0' (G.703), '1' (V.35), '2' (RS422), or '3'
(RS232).
p85 = nnnnn, where 'nnnnn' is the currently programmed baud
rate.
p86 = nnnnn, where 'nnnnn' is the currently programmed baud
rate.
p87 = n, where 'n' is the currently programmed character length.
p88 = n, where 'n' is the currently programmed character length.