Rockwell Automation 1771-QDC, D17716.5.86(Passport) PLASTIC MOLDING MODULE - Manual (Page 171)

Span Your Valves
Chapter 9
9-14
Span your clamp close velocity (flow) valve(s) for optimum velocity
performance. Do this in three parts:
Confirm critical values
Span your clamp close velocity (flow) valve(s)
Test valve linearity with a velocity vs. position profile
Important: You may omit this section if you have the right information on
valve spanning. Many injection molding machine OEMs and hydraulic
valve manufacturers provide data on spanning the working range of valves
used on their machines. If this information is available from your OEM
for your machine’s clamp close velocity valve(s), enter the values into
velocity control limits FCC45-48, SCC45-48, and TCC45-45 and proceed
to Span your Open Slow Valves.
Confirm Critical Values
Important: Confirm that your entries for configuration values (chapter 7)
and profile values (chapter 8) for clamp close profiles are as follows:
On Worksheet: Confirm Your Configuration: With These Words or Bits: ProĆSet Addr.
7ĆA, 7ĆB, 7ĆC QDC module output to which you connected
your selected velocity control valve
FCC02ĆB02,B01,B00 = your selection
SCC02ĆB02,B01,B00 = your
selection
TCC02ĆB02,B01,B00 = your selection
B37/22, 21, 20
B37/86, 85, 84
B37/150,149,148
Your unselected setĆoutput values for outputs
1Ć4
FCC09Ć12 = your value
SCC09Ć12 = your value
TCC09Ć12 = your value
N43:5Ć8
N43:65Ć68
N43:125Ć128
All ramping is disabled with zero ramp rates FCC17Ć20 = FCC25Ć28 = 0
SCC17Ć20 = SCC25Ć28 = 0
TCC17Ć20 = TCC25Ć28 = 0
N43:13Ć16 N43:21Ć24
N43:73Ć76 N43:81Ć84
N43:133Ć136
N43:141Ć144
Velocity limits:
Minimum Control Limit
Maximum Control Limit
Selected Velocity Valve, Output for Min
Selected Velocity Valve, Output for Max
FCC45=SCC45=TCC45=0
FCC46=SCC46=TCC46=sys vel
FCC47=SCC47=TCC47=your value
FCC48=SCC48=TCC48=your value
N43:41, 101, 161
N43:42, 102, 162
N43:43, 103, 163
N43:44, 104, 164
8ĆA Selected inches/second as velocity units CPC03ĆB14 = 1 B37/302
Mold protection CPC03ĆB11 = 0 B37/299
Logical bridge CPC03ĆB10 = B09 = B08 = 0 B37/298, 297, 296
Expert Response Compensation (ERC) = Off CPC04ĆB15 = B13ĆB08 = 1 B37/319, 317Ć312
OpenĆloop control CPC04ĆB07 = B05ĆB00 = 1 B37/311, 309Ć304
EndĆof Segment position setpoints CPC11,14,17 N43:247, 250, 253
Start LPC position CPC61 N43:297
Mold Safe Position CPC62 N43:298
If these are not your current values, we suggest that you correct them now
using the download procedure discussed in chapter 4.
Span Your Clamp Close
Velocity (Flow) Valve(s)