NORD Drivesystems BU0505 - Manual (Page 133)

5 Parameters
BU 0505 GB-1013 133
P546
[-01]
...
[-05]
Digital Bus setpoint
(Function of bus setpoint)
S P
0 ... 57
{ [-01] = 1 }
all other { 0 }
In this parameter, during bus actuation a function is allocated to the setpoint provided.
NOTE: The setpoints 4 and 5 must be supported by the relevant bus module. For further
details please refer to the manual for the frequency inverter (P400, P546), the
relevant BUS operating instructions or the manuals BU 0510 / BU0550.
[-01] = Bus setpoint 1 [-02] = Bus setpoint 2 [-03] = Bus setpoint 3
[-04] = Bus setpoint 4 [-05] = Bus setpoint 5
Pos : 309 /Anleit ungen/5. / 6. Parametrier ung [BU 0500 / BU 0200]/ Par ameter/ P500-P599/ Paramet er P546 – Funkti on Bus-Soll wert e, Ei nst ellungen [ SK 5xxE] @ 2\ mod_1354267859195_388.doc x @ 51897 @ @ 1
0 = Off 16 = Process controller lead
1 = Setpoint frequency 17 = BusIO In Bits 0...7
2 = Torque current limit (P112) 18 = Curve travel calculator
3 = Actual frequency PID 19 = Set relays, "Output status"
(P434/441/450/455=38)
4 = Frequency addition 20 = Set analog output (P418=31)
5 = Frequency subtraction 21 = ... 45 reserved from SK 530E and above à
BU 0510
6 = Current limit (P536) 46 = Setpoint Torque processreg., "Setpoint
torque process controller"
7 = Maximum frequency (P105) 47 = reserved from SK 530E and above à
BU 0510
8 = Actual PID frequency limited 48 = Motor temperature (SK 540E and above)
9 = Actual PID frequency monitored 49 = reserved from SK 540E and above à
BU 0510
10 = Torque servo mode (P300) 53 = d-correction F process (SK 540E and
above)
11 = Torque precontrol (P214) 54 = d-correction Torque (SK 540E and above)
12 = Reserved 55 = d-correction F+torque (SK 540E and
above)
13 = Multiplication 56 = reserved from SK 540E and above à
BU 0510
14 = Process controller actual value 57 = reserved from SK 540E and above à
BU 0510
15 = Process controller setpoint
Scaling details: See Section 8.8
Pos : 312 /Anleit ungen/5. / 6. Parametrier ung [BU 0500 / BU 0200]/ Par ameter/ P500-P599/ Paramet er P549 – Funkti on Poti-Box @ 0\ mod_1328098389279_388. doc x @ 12008 @ @ 1
P549
Pot Box function
(PotentiometerBox function)
S
0 ... 16
{ 0 }
In this parameter, the setpoint of the PotentiometerBox (SK TU3-POT) is assigned with a
function. (An explanation can be found in the description of P400.)
As of software version 1.7 R0, on setting 4 or 5, the ControlBox or the ParameterBox are also set
to function as suppliers of auxiliary setpoints. (see Section 0)
0 = Off
1 = Setpoint frequency
2 = Torque current limit
3 = Actual frequency PID
4 = Frequency addition
5 = Frequency subtraction
6 = Current limit
7 = Maximum frequency
8 = Actual PID frequency limited
9 = Actual PID frequency monitored
10 = Servo mode torque
11 = Torque precontrol
12 = Reserved
13 = Multiplication
14 = Process controller actual value
15 = Process controller setpoint
16 = Process controller lead
Pos : 313 /Anleit ungen/5. / 6. Parametrier ung [BU 0500 / BU 0200]/ Par ameter/ P500-P599/ Paramet er P550 – C ontrol Box Auf träge @ 0\mod_1328098468764_388. doc x @ 12031 @ @ 1