beautypg.com

West Control Solutions Pro-EC44 User Manual

Page 167

background image

Pro-EC44 2-Loop Graphical Profile Controller & Recorder

Pro-EC44 Product Manual - 59540-1 October 2013

Page 160

Pre-Tune Secondary Status

Value

Loop 2 Pre-Tune Secondary Status

Dec

4441

20825 41650

RW

0

No Additional Information

Hex

1159

5159

A2B2

1

PV within 5% (Pre-Tune cannot run)

2

Manual Control Enabled (Pre-Tune cannot run)

3

Control has On/Off element (Pre-Tune cannot run)

4

Input not valid (Pre-Tune cannot run)

5

Control Disabled (Pre-Tune cannot run)

6

Profile Running (Pre-Tune cannot run)

7

Setpoint Ramping (Pre-Tune cannot run)

Self-Tune Secondary Status

Value

Loop 2 Self-Tune Secondary Status

Dec

4442

20826 41652

RW

0

No Additional Information

Hex

115A

515A

A2B4

2

Manual Control Enabled (Self-Tune cannot run)

3

Control has On/Off element (Self-Tune cannot run)

4

Input not valid (Self-Tune cannot run)

5

Control Disabled (Self-Tune cannot run)

Loop 2 Anti Wind-up Limit

Loop 2 Anti Wind-up Limit

Dec

4491

20875 41750

RW

Power level where integral action is suspended.

Adjustable from 10.0 to 100.0% of PID power.

Hex

118B

518B

A316

Loop 2 Motor Travel Time

Loop 2 Motor Travel Time

Dec

4443

20827 41654

RW

The motor travel time (from fully open to fully closed) for 3-point

stepping VMD control. Adjustable from 5 to 300 seconds.

Hex

115B

515B

A2B6

Loop 2 Minimum Motor On Time

Loop 2 Minimum Motor On Time

Dec

4444

20828 41656

RW

Minimum drive effort to begin moving valve for 3-point stepping

VMD control. In seconds, from 0.02 to 1/10 of Motor Travel Time

Hex

115C

515C

A2B8

Loop 2 Valve Break Action

Value

Loop 2 Sensor Break Action For VMD Control

Dec

4501

20885 41770

RW

0

Close Valve Output On

Hex

1195

5195

A32A

1

Open Valve Output On

Loop 2 Minimum Valve Position

Loop 2 Minimum Valve Position

Dec

4476

20860 41720

RW

Minimum position to drive valve in VMD Mode

from the valve close limit+1% to 100.0%

Hex

117C

517C

A2F8

Loop 2 Maximum Valve Position

Loop 2 Maximum Valve Position

Dec

4477

20861 41722

RW

Maximum position to drive valve in VMD Mode.

From 0.0% to the valve open limit-1%

Hex

117D

517D

A2FA

Loop 2 PID Set Select

Value

Loop 2 PID Set Selection

Dec

4467

20851 41702

RW

0

PID Set 1

Hex

1173

5173

A2E6

1

Gain Schedule Selected by SP

2

Gain Schedule Selected by PV

3

PID Set 2

4

PID Set 3

5

PID Set 4

6

PID Set 5

PID Set 2 - Primary Prop Band

PID Set 2 Primary Proportional Band For Loop 2

Dec

4447

20831 41662

RW

Primary Proportional Band for Gain Set 2.

1 display unit to 9999 units,

but limited to 10 x scaled input span. 0 = On-Off control

Hex

115F

515F

A2BE

PID Set 2 - Secondary Prop Band

PID Set 2 Secondary Proportional Band For Loop1

Dec

4448

20832 41664

RW

Secondary Proportional Band for Gain Set 2.

1 display unit to 9999 units,

but limited to 10 x scaled input span. 0 = On-Off control

Hex

1160

5160

A2C0

This manual is related to the following products: